Canon imagePROGRAF IPF700 - Page 126

Contents
6.1.4.20 03130031-2F2A Feed roller home position error........................................................ 6-12
6.1.4.21 03130031-2F3A valve open/close error ...................................................................... 6-12
6.1.4.22 03800200-2802/03800400-2803/03800300-2801 Printhead error .......................... 6-12
6.1.4.23 03800500-280C Defective printhead nozzle .............................................................. 6-13
6.1.4.24 03800500-2F2F/03800500-2F30 Head management sensor error......................... 6-13
6.1.4.25 03810101-2501/03810102-2502/03810103-2503/03810104-2500/03810106-2506/
03810106-2507 No ink error ................................................................................................... 6-13
6.1.4.26 03810201-2581/03810202-2582/03810203-2583/03810204-2580/03810206-2586/
03810206-2587 Tank level error 1 ......................................................................................... 6-14
6.1.4.27 03810201-2591/03810202-2592/03810203-2593/03810204-2590/03810206-2596/
03810206-2597 Tank level error 2 ......................................................................................... 6-14
6.1.4.28 03830101-2521/03830102-2522/03830103-2523/03830104-2520/03830106-2526/
03830105-2527 Ink tank is not installed. ( This error occurs when the ink tank is replaced.)
6-15
6.1.4.29 03830201-2541/03830202-2542/03830203-2543/03800204-2540/03830206-2546/
03830206-2547 Invalid ink tank ID......................................................................................... 6-15
6.1.4.30 03830301-2561/03830302-2562/03830303-2563/03830304-2560/03830306-2566/
03830306-2567 Ink tank EEPROM error .............................................................................. 6-15
6.1.4.31 03841001-2819/03841001-281B/03841101-2818/03841201-2816/03841201-2817
Maintenance cartridge error .................................................................................................... 6-15
6.1.4.32 03861001-2405/03861001-2406 Borderless printing error ....................................... 6-16
6.1.4.33 03862000-2E09 Insufficient roll media error................................................................ 6-16
6.1.4.34 03870001-2015 Cutter error........................................................................................... 6-16
6.1.4.35 03900001-4042/03900001-4049 Firmware error ........................................................ 6-17
6.1.4.36 E194-4034 Sensor calibration error .............................................................................. 6-17
6.1.5 Troubleshooting When Service Call Errors Occur ............................................. 6-17
6.1.5.1 E141-4046 Recovery system's rotation count reached 50,000 .................................. 6-17
6.1.5.2 E144-4047 Supply system's count error ........................................................................ 6-17
6.1.5.3 E146-4001 Borderless/idle ejection/mist collection count full ..................................... 6-18
6.1.5.4 E161-403E Abnormally high head temperature............................................................ 6-18
6.1.5.5 E194-404A Non-discharge detection count error ......................................................... 6-18
6.1.5.6 E196-4040/E196-4041/E196-4042/E196-4043/E196-4044/E196-4045 Main controller
PCB error.................................................................................................................................... 6-18
6.1.5.7 E198-401C/E198-401D/E198-401E RTC error ............................................................ 6-19
6.2 Location of Connectors and Pin Arrangement ............................................ 6-19
6.2.1 Main controller PCB ................................................................................................ 6-19
6.2.2 Carriage relay PCB ................................................................................................. 6-28
6.2.3 Head relay PCB....................................................................................................... 6-35
6.3 Version Up ........................................................................................................ 6-40
6.3.1 Firmware Update Tool............................................................................................ 6-40
6.4 Service Tools.................................................................................................... 6-41
6.4.1 List of Tools .............................................................................................................. 6-41
6.4.2 Using the Cover Switch Tool ................................................................................. 6-42