Clear-Com Eclipse HX series - Page 195

230 pages

Save Page as PDF

To Next Page

To Previous Page

Eclipse | Upgrade Guide

Page 195

Figure 16-5: FPGA upgrade completed

c. Reset the card to complete the upgrade.

Main Page

Default Chapter3
- Table of Contents3
1 Important Safety Instructions6
- Safety Symbols7
- Mains Power Cord7
2 Introduction8
- Planning the Upgrade to Eclipse HX8
3 Quick Reference: Upgrading to Eclipse HX V9.117
- Upgrading from 5.2.517
- Upgrading from 7.020
- Upgrading from 7.123
- Upgrading from 7.526
- Upgrading from 7.629
- Upgrading from 8.032
- Upgrading from 8.535
- Upgrading from 8.5.137
- Upgrading from 8.5.240
- Upgrading from 8.742
- Upgrading from 8.845
- Upgrading from 9.047
4 Upgrading to Eclipse HX V9.150
- Backing up Your ECS V5.2.5 Configurations50
- Backing up Your EHX 7.X/8.X/9.0 Configurations50
- Installing EHX and Dynam-EC Clients50
- Importing Your Configurations into EHX51
- Updating Dynam-EC52
5 Upgrading the CPU Cards53
- Changing the CPU Card PROM53
- Changing the CPU Card RAM54
- Changing the CPU Card DIP Switches55
- Upgrading the CPU Card Application Code55
- Setting the Matrix Type66
- Checking the CPU Card Application Code Version67
- Upgrading CPU Card U53 CPLD67
- Upgrading CPU Card U1 CPLD69
- Upgrading the CPU Card U53 CPLD Code with Xilinx Tools71
- Upgrading the CPU Card U1 CPLD Code with Xilinx Tools73
- Downloading a Test Configuration to the CPU Card Using EHX75
- Forcing the CPU Card to the Factory Default IP Address76
6 Upgrading the Eclipse HX-Pico77
- Changing the Eclipse HX-Pico PROM77
- Changing the Eclipse HX-Pico RAM78
- Changing the Eclipse HX-Pico DIP Switches80
- Upgrading the Eclipse HX-Pico MVX Code90
- Checking the Eclipse HX-Pico App Code and MVX Code Versions98
- Upgrading the Eclipse HX-Pico CPLD and FPGA Code with Xilinx Tools99
- Download a Test Configuration into the Eclipse HX-Pico Using EHX102
- Forcing the Eclipse HX-Pico to the Factory Default IP Address102
7 Upgrading the MVX-A16 Card104
- Identifying MK I and MK II MVX-A16 Cards104
- Upgrading the MVX-A16 MK I or MK II Boot And/Or App Code104
- Checking the MVX-A16 MK I or MK II Boot and Application Code Version110
- Upgrading the MVX-A16 MK I or MK II Card FPGA with Xilinx Tools111
8 Upgrading E-FIB Cards120
- Upgrading E-FIB Card FPGA with Xilinx Tools120
9 Upgrading E-QUE Cards123
- Identifying MK1 and MK2 E-QUE Cards123
- Upgrading the E-QUE Card (MK1)124
- Upgrading the E-QUE Card (MK2)129
- Upgrading the E-QUE Card (MK1 and MK2) FPGA with Xilinx Tools136
- Upgrading the E-QUE Card (MK1) Boot ROM138
- Upgrading the E-QUE Card (MK2) Boot ROM139
10 Upgrading IVC-32 and LMC-64 Cards145
- Identifying MK1 and MK2 IVC-32 / LMC-64 Cards145
11 Upgrading E-MADI64 Cards147
- Identifying MK1 and MK2 E-MADI64 Cards147
- Upgrading the E-MADI64 Boot Code149
- Upgrading the E-MADI64 Application, DSP and FPGA Code Using EHX152
- Upgrading the E-MADI64 FPGA Using the Xilinx Tool Set155
12 Upgrading E-DANTE64-HX Cards158
13 Upgrading Cellcom®/Freespeak® Wireless Systems161
14 Upgrading Panels162
- Upgrading Panels Using EHX162
- Upgrading Panel Application Code Manually165
- Manually Upgrading V-Series Panels177
15 Upgrading the TEL-14 Module184
- Upgrading the TEL-14 Hardware184
- Upgrading the TEL-14 Firmware186
16 Upgrading the AES-6 Module189
- Upgrading AES-6 FPGA190
17 Upgrading Freespeak II™ Wireless Systems196
- Upgrading Freespeak II Beltpacks and Antennas Centrally Using EHX196
- Upgrading Freespeak II Beltpacks and Antennas Via USB198
Appendix A: CPU Card Layout201
Appendix B: CPU Card DIP Switches202
Appendix C: Pico Card Layout204
Appendix D: Eclipse HX-Pico CPU DIP Switches205
Appendix E: Hitachi Renesas Flash Development Tool207
Appendix F: Tftputil213
Appendix G: Tera Term216
Appendix H: Flash Magic218
Appendix I: I-Station Converter Cable Wiring and Rear Panel222
Layouts222
Appendix J: Xilinx Tools224
Appendix K: Clear-Com End User Software License225

Clear-Com Eclipse HX series - Page 195

Table of Contents

Related product manuals