Clear-Com FreeSpeak II FSII-TCVR-24 User Manual

Name: Clear-Com FreeSpeak II FSII-TCVR-24
Brand: Clear-Com
Rating: 4 (1 reviews)

102 pages

To Next Page

To Previous Page

User Guide| FreeSpeak II for Eclipse HX

Beltpack headset tones/alerts

Menu button

Mid beep.

Mid, on 100ms, off 100ms.

Triggers on entering menu mode.

Power button

Mid beep.

Mid, on 100ms, off 100ms, repeated while power button pressed.

Listen again

Low beep.

Low, on 100ms, off 100ms.

4.2.4 Front controls

Page 26

Table of Contents3
Important Safety Instructions6
Safety Symbols7
Introduction to Freespeak8
An FS II Communication System8
Freespeak II with an FSII Transceiver (1.9 and 2.4)9
Freespeak II with an FSII IP Transceiver10
FSII 1.9 Ghz/Fsii 2.4 Ghz11
National Radio Carrier Frequencies12
Installing a System14
Installing and Removing an E-IPA-HX Card14
Adding an E-IPA-HX Card to the Software14
Adding the E-Que Card for an FS II Transceiver or Splitter to the Matrix15
Connecting to Transceivers17
Clear-Com Cable Recommendations19
Operating the Wireless Beltpack21
Overview of the Wireless Beltpack21
Beltpack User Controls24
Using the Beltpack29
Programming on the Beltpack35
Introduction to Programming on the Beltpack35
Configuring the Beltpack Volume Settings36
Configuring the Beltpack Headset37
Configuring the Beltpack Microphone38
Configuring the Beltpack Display and Leds39
Configuring the Beltpack Alarm Options41
Selecting the Beltpack Role Default Set43
Selecting the Beltpack Administration43
Setting the Listen Again Option44
Control Audio on Keys C & D (Beltpack)(Advanced Menu Option Only)45
Accessing Beltpack Information45
Setting Display Mode46
Setting System Connect46
Enabling over the Air (OTA) Registration Mode from a Beltpack46
Performing a Site Survey48
Operating the FS II IP Transceiver (IPT)49
IP Rating (Protection Marking)49
FS II IP Transceiver Connector Panel50
IP Transmitter Leds50
IP Transceiver Fans and Filters51
Reset the IPT to Default54
Transceiver Standalone Mode54
Connecting the FS Transceivers to a Matrix54
Cabling the IP Transceivers58
Configuring the E-IPA-HX Card for Freespeak II59
Adding Transceivers60
Powering the Transceiver65
Upgrading the FS II IP Transceiver Firmware66
Upgrading from the Matrix66
Upgrading by USB Connection67
Port Security Settings67
Network and Synchronization67
General Network and Switching Rules68
Beltpack Support Capacities for FS II IP Transceivers68
Coverage Areas under Various Conditions69
FS II Transceiver Setup Rules and Tips69
Spare Parts70
Operating the FS II Transceiver71
IP Rating (Protection Marking)71
FS II Transceiver Connector Panel71
Cabling the FS II Transceivers72
Beltpack Support Capacities for FS II Transceivers77
Placing the Transceivers and Splitters77
Determining Coverage Areas79
Coverage Areas under Various Conditions80
FS II Transceiver Setup Rules and Tips80
Doing a Site Survey to Determine Coverage Areas81
Registering Beltpacks85
Upgrading FS II Transceiver Firmware86
Upgrading by USB Connection86
Upgrading by Wireless Connection86
Using the Freespeak II Base Splitter (FSII-SPL)88
Configuration Using a Splitter with Cat 5/6 RJ45 Connection88
Configuration Using a Splitter with Fiber Connection89
Splitter (FSII-SPL) Rear Connectors90
Splitter (FSII-SPL) Front Panel91
Using a Transceiver with a Fiber Connection91
Splitter Software Version (FSII-SPL)93
Specifications95
Freespeak II Beltpack95
Freespeak IP Transceiver96
Freespeak II Transceiver96
Freespeak II Transceiver Splitter97
Transmission Method97
Notice about Specifications97
Regulatory Compliance98
FCC Notice98
FCC/IC/EC RF Exposure Warning98
Industry Canada Compliance Statement99
Korean Notice99
KCC 2.4Ghz Warning99
European Union (CE Mark)99
Taiwan Statements100
Customs Union EAEU101
Waste Electrical and Electronic Equipment (WEEE)101

Brand	Clear-Com
Model	FreeSpeak II FSII-TCVR-24
Category	Intercom System
Language	English

Clear-Com FreeSpeak II FSII-TCVR-24 User Manual

Table of Contents

Questions and Answers:

Clear-Com FreeSpeak II FSII-TCVR-24 Specifications

Related product manuals