Page 68
2 = Enabled During Dialling in Armed State only
3 = Enabled During Dialling in Monitor Mode State only
4 = Enabled Throughout the call in Disarm State only
5 = Enabled Throughout the call in Armed State only
6 = Enabled Throughout the call in Monitor Mode State only
7 = Listen-in Enabled when the panel answers a call
8 = Enabled at All Times
**Listen-in via internal speaker Options**
P607E Listen-in via internal speaker P443E Options (Default = Off) Page 54
1 = Enabled During Dialling in Disarm State only
2 = Enabled During Dialling in Armed State only
3 = Enabled During Dialling in Monitor Mode State only
4 = Enabled Throughout the call in Disarm State only
5 = Enabled Throughout the call in Armed State only
6 = Enabled Throughout the call in Monitor Mode State only
7 = Listen-in Enabled when the panel answers a call
8 = Enabled at All Times
Partition “B” Primary Output Options
P611E-P618E OPTIONS
P611E Area "B" primary options for output #1 - Default 1 1 = Standard zone activation's Page 23
P612E Area "B" primary options for output #2 - Default 1 & 2 2 = Stay Mode activation's Page 23
P613E Area "B" primary options for output #3 - Default 1 3 = Radio key chirps Page 23
P614E Area "B" primary options for output #4 - Default 1 4 = All zones sealed (Ready) Page 23
P615E Area "B" primary options for output #5 - Default 1 5 = 2 sec pulse arm/disarm Page 23
P616E Area "B" primary options for output #6 - Default 1 6 = Day zone activation's Page 23
P617E Area "B" primary options for output #7 - Default 1 7 = Spare Page 23
P618E Area "B" primary options for output #8 - Default 1 8 = Spare Page 23
Partition “B” Keypad Options
P619E Arm key can disarm during exit - Default 1-8 Page 25
P620E Stay key can disarm during Stay armed state - Default 1-8 Page 25
Partition “B” Secondary Output Options
P621E-P628E OPTIONS
P621E Area "B" secondary options for output #1 - Default 0 1 =Any bypass Page 24
P622E Area "B" secondary options for output #2 - Default 0 2 = Auto bypass warning Page 24
P623E Area "B" secondary options for output #3 - Default 0 3 = Entry beeps Page 24
P624E Area "B" secondary options for output #4 - Default 0 4 = Exit beeps Page 24
P625E Area "B" secondary options for output #5 - Default 0 5 = Follow Set Arming Page 24
P626E Area "B" secondary options for output #6 - Default 0 6 = Follow Stay Arming Page 24
P627E Area "B" secondary options for output #7 - Default 0 7 = Follow Unset Page 24
P628E Area "B" secondary options for output #8 - Default 0 8 = Spare Page 24
Programming Partition “B” Auto Arm/Disarm Time-zones
P629E Time Zones used for Area "B" auto arming /disarming- Default 0 (see P632E) Page 25
Partition “B” Misc Options
P630E Misc partition options 1 - Default 0
1 = Cannot Arm if not sealed Page 25
2 = “Arm” required before code
3 = “Stay” required before code
4 = Code required to arm
5 = Code required to “Bypass” zones
6 = Control/Chime disables day zones
7 = Repeat System PA messages
8 = Spare
P631E Misc partitions options 2 - Default 3,4,6 1 = Key-switch enabled Page 26
2 = Use 2nd Key-switch
3 = Key-switch ARM's/STAY
4 = Pendant chirps when armed
5 = Pendant chirps when in Stay Mode
6 = 2 sec pulse at set
To Next Page
Loading...
