Page 71
7 = 4+2 10pps (Handshake 2300/ Tone 1800)
8 = 4+2 10pps (Handshake 2300/ Tone 1900)
9 = 4+2 20pps (Handshake 1400/ Tone 1800)
10= 4+2 20pps (Handshake 1400/ Tone 1900)
11= 4+2 20pps (Handshake 2300/ Tone 1800)
12= 4+2 20pps (Handshake 2300/ Tone 1900)
13= 4+2 DTMF
**Telephone Number Reporting Options**
P703E Options for Telephone # 1 P393E-P398E Options (Default =1,4,5) Page 55
P704E Options for Telephone # 2 1 = Monitor Call Progress
P705E Options for Telephone # 3 2 = Blind Dial
P706E Options for Telephone # 4 3 = Use Group Numbers for Contact ID
P707E Options for Telephone # 5 4 = Send Restores
P708E Options for Telephone # 6 5 = Send Test Calls
6 = Add Ph Pre-fix to telephone number
Partition “C” Primary Output Options
P711E-P718E OPTIONS
P711E Area “C” primary options for output #1- Default 1 1 = Standard zone activation's Page 23
P712E Area “C” primary options for output #2 - Default 1 & 2 2 = Stay Mode activation's Page 23
P713E Area "C" primary options for output #3 - Default 1 3 = Radio key chirps Page 23
P714E Area "C" primary options for output #4 - Default 1 4 = All zones sealed (ready) Page 23
P715E Area "C" primary options for output #5 - Default 1 5 = 2 sec pulse on arm/disarm Page 23
P716E Area "C" primary options for output #6 - Default 1 6 = Day zone activation's Page 23
P717E Area "C" primary options for output #7 - Default 1 7 = Spare Page 23
P718E Area "C" primary options for output #8 - Default 1 8 = Spare Page 23
Partition “C” Keypad Options
P719E Arm key can disarm during exit - Default 1-8 Page 25
P720E Stay key can disarm during Stay armed state - Default 1-8 Page 25
Partition “C” Secondary Output Options
P721E-P728E OPTIONS
P721E Area "C" secondary options for output #1 - Default 0 1 = Any exclude Page 24
P722E Area "C" secondary options for output #2 - Default 0 2 = Auto exclude warn Page 24
P723E Area "C" secondary options for output #3 - Default 0 3 = Entry beeps Page 24
P724E Area "C" secondary options for output #4 - Default 0 4 = Exit Beeps Page 24
P725E Area "C" secondary options for output #5 - Default 0 5 = Control Page 24
P726E Area "C" secondary options for output #6 - Default 0 6 = Follow Set Arming Page 24
P727E Area "C" secondary options for output #7 - Default 0 7 = Follow Stay Arming Page 24
P728E Area "C" secondary options for output #8 - Default 0 8 = Follow Unset Page 24
Programming Partition “C” Auto Arm/Disarm Time-zones
P729E Time Zones used for Area "C" auto arming /disarming- Default 0 (see P732E) Page 25
Partition “C” Misc Options
P730E Misc partition options 1 - Default 0 1 = Cannot Arm if not sealed Page 25
2 = “Arm” required before code
3 = “Stay” required before code
4 = Code required to arm
5 = Code required to “Bypass” zones
6 = Control disables day zones
7 = Repeat System PA messages
8 = Spare
P731E Misc partition options 2 - Default 3,4,6 1 = Key-switch enabled Page 26
2 = Use 2nd Key-switch
To Next Page
Loading...
