xStack DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch
122
forward packets to this VLAN if the tag
to forward packets to this VLAN if the
orward packets to this VLAN if
instruct the Switch to forward packets to this VLAN if the
ll instruct the Switch to forward packets to this VLAN if the tag
o this VLAN if the
ard packets to this VLAN if
to this VLAN if the tag
Novell NetWare 802.3 (IPX - Internet Packet Exchange).
IPX 802.2 - Using this parameter will instruct the Switch to
in the packet header is concurrent with this protocol. This packet header information is defined by
Novell NetWare 802.2 (IPX - Internet Packet Exchange).
IPX SNAP - Using this parameter will instruct the Switch
tag in the packet header is concurrent with this protocol. This packet header information is
defined by Novell and the Sub Network Access Protocol (SNAP).
IPX Ethernet2 - Using this parameter will instruct the Switch to f
the tag in the packet header is concurrent with this protocol. This packet header information is
defined by Novell Ethernet II Protocol.
Apple Talk - Using this parameter will
tag in the packet header is concurrent with this protocol. This packet header information is
defined by the AppleTalk protocol.
DEC LAT - Using this parameter wi
in the packet header is concurrent with this protocol. This packet header information is defined by
the Digital Equipment Corporation (DEC) Local Area Transport (LAT) protocol.
SNA 802.2 - Using this parameter will instruct the Switch to forward packets t
tag in the packet header is concurrent with this protocol. This packet header information is
defined by the Systems Network Architecture (SNA) 802.2 Protocol.
SNA Ethernet2 - Using this parameter will instruct the Switch to forw
the tag in the packet header is concurrent with this protocol. This packet header information is
defined by the Systems Network Architecture (SNA) Ethernet II Protocol.
Net Bios - Using this parameter will instruct the Switch to forward packets
in the packet header is concurrent with this protocol. This packet header information is defined by
the NetBIOS Protocol.
XNS - Using this parameter will instruct the Switch to forward packets to this VLAN if the tag in
Switch to forward packets to this VLAN if the tag in
ckets to this VLAN if the tag in
the Switch to forward packets to this VLAN if the
packets with this hexadecimal
Switch will examine the octet of the
the packet header is concurrent with this protocol. This packet header information is defined by
the Xerox Network Systems (XNS) Protocol.
VINES - Using this parameter will instruct the
the packet header is concurrent with this protocol. This packet header information is defined by
the Banyan Virtual Integrated Network Service (VINES) Protocol.
IPv6 - Using this parameter will instruct the Switch to forward pa
the packet header is concurrent with this protocol. This packet header information is defined by
the Internet Protocol Version 6 (IPv6) Protocol.
User Defined - Using this parameter will instruct
tag in the packet header is concurrent with this protocol defined by the user. This packet header
information is defined by entering the following information:
User Defined Packet ID - Specifies that the VLAN will only accept
802.1Q Ethernet type value in the packet header. The user may define an entry, in the
hexadecimal form (ffff) to define the packet identification. (The user only need enter the final four
integers of the hexadecimal format to define the packet ID – {hex 0x0 0xffff}) This field is only
operable if userDefined is selected in the Protocol ID field.
Encap [Ethernet | LLC | SNAP | All] – Specifies that the
packet header referring to one of the protocols listed (Ethernet, LLC or SNAP), looking for a
match of the hexadecimal value previously entered. All will instruct the Switch to examine the
total packet header. After a match is found, the Switch will forward the packet to this VLAN. This
field is only operable if userDefined is selected in the Protocol ID field.
Port Settings
Allows an individual port to be specified as member of a VLAN.
Tag
Specifies the port as either 802.1Q tagging or 802.1Q untagged. Checking the box will designate
the port as Tagged.
None
ecified as a non-VLAN member. Allows an individual port to be sp
Egress
er ports are ports Select this to specify the port as a static member of the VLAN. Egress memb
To Next Page
Loading...
