Danfoss VLT AQUA Drive FC 202 Programming Guide

1-03 Torque Characteristics
Option: Function:
but if the motor power factor cos phi requires
tuning, an AMA function can be carried out
using parameter 1-29 Automatic Motor Adaptation
(AMA). It is rarely necessary to adjust the motor
power factor parameter manually.
NOTICE
Parameter 1-03 Torque Characteristics has no eect when
parameter 1-10 Motor Construction = [1] PM, non-salient
SPM.
1-04 Overload Mode
Select the torque level in overload mode.
Option: Function:
[0] High torque Allows up to 160% overtorque for
undersized motors.
[1] * Normal torque Allows up to 110% overtorque.
1-06 Clockwise Direction
Option: Function:
NOTICE
This parameter cannot be adjusted while
the motor is running.
This parameter denes the term clockwise
corresponding to the LCP direction arrow. Used for
easy change of direction of shaft rotation without
swapping motor wires.
[0] * Normal The motor shaft turns in clockwise direction when
the frequency converter is connected U⇒U, V⇒V,
and W⇒W to the motor.
[1] Inverse Motor shaft turns in counterclockwise direction
when the frequency converter is connected U⇒U,
V⇒V, and W⇒W to the motor.
3.3.2 1-1* Motor Selection
NOTICE
This parameter group cannot be adjusted while the
motor is running.
The following parameters are active depending on the
setting in parameter 1-10 Motor Construction.
Parameter 1-10 Motor
Construction
[0]
Asynchro
-
nous
[1] PM
Motor
non-
salient
[2] PM
Motor
Salient
IPM
[3]
SynRM
Motor
Parameter 1-00 Cong-
uration Mode
x x x x
Parameter 1-10 Motor
Construction
[0]
Asynchro
-
nous
[1] PM
Motor
non-
salient
[2] PM
Motor
Salient
IPM
[3]
SynRM
Motor
Parameter 1-03 Torque
Characteristics
x – - -
Parameter 1-06 Clockwi
se Direction
x x x x
Parameter 1-14 Dampi
ng Gain
– x x x
Parameter 1-15 Low
Speed Filter Time
Const.
– x x x
Parameter 1-16 High
Speed Filter Time
Const.
– x x x
Parameter 1-17 Voltage
lter time const.
– x x x
Parameter 1-20 Motor
Power [kW]
x – – –
Parameter 1-21 Motor
Power [HP]
x – – –
Parameter 1-22 Motor
Voltage
x – – –
Parameter 1-23 Motor
Frequency
x – – –
Parameter 1-24 Motor
Current
x x x x
Parameter 1-25 Motor
Nominal Speed
x x x x
Parameter 1-26 Motor
Cont. Rated Torque
– x x x
Parameter 1-28 Motor
Rotation Check
x x x x
Parameter 1-29 Autom
atic Motor Adaptation
(AMA)
x x x x
Parameter 1-30 Stator
Resistance (Rs)
x x x x
Parameter 1-31 Rotor
Resistance (Rr)
x – – –
Parameter 1-35 Main
Reactance (Xh)
x – – –
Parameter 1-37 d-axis
Inductance (Ld)
– x x x
Parameter 1-39 Motor
Poles
x x x x
Parameter 1-40 Back
EMF at 1000 RPM
– x x –
Parameter 1-44 d-axis
Inductance Sat. (LdSat)
– – – x
Parameter 1-45 q-axis
Inductance Sat. (LqSat)
– – x –
Parameter 1-46 Positio
n Detection Gain
– x x x
Parameter Description Programming Guide
MG20OB02 Danfoss A/S © 05/2018 All rights reserved. 41
3 3

Danfoss VLT AQUA Drive FC 202 Specifications

General

Brand	Danfoss
Model	VLT AQUA Drive FC 202
Category	DC Drives
Language	English