Emerson X-STREAM XE - Page 10

Emerson Process Management GmbH & Co. OHGTOC-8
X-STREAM XE
Instruction Manual
HASXEE-IM-HS
10/2012
Fig. 3-6: Electrochemical O
2
Sensor - Assembly .................................3-8
Fig. 3-7: Electrochemical Reaction of Oxygen Sensor .............................3-9
Fig. 3-8: Cover for EO2 Sensor Block At Rear Panel .............................3-10
Fig. 3-9: Trace Oxygen Sensor Design Principle ................................3-11
Fig. 3-10: Cover for TO2 Sensor Block At Rear Panel .............................3-12
Fig. 3-11: Wheatstone Bridge................................................3-13
Fig. 3-12: TC Cell, Exterior View, Thermal Isolation Removed.......................3-14
Fig. 3-13: TC Cell, Sectional View ............................................3-14
Fig. 3-14: Trace Moisture Sensor Assembly .....................................3-15
Fig. 4-1: X-STREAM Enhanced Analyzers - Scope of Supply .......................4-1
Fig. 4-3: Installation in Bypass Mode ..........................................4-6
Fig. 4-2: Labelling of Gas Connectors (example) .................................4-6
Fig. 4-4: X-STREAM XEGK - Rack Mount Version Rear Panel ......................4-9
Fig. 4-5: X-STREAM XEGP - Table Top Version Rear Panel .......................4-10
Fig. 4-6: X-STREAM XEGP - Rear Panel, Terminal Adapters and Front Side Brackets...4-11
Fig. 4-7: Socket X1 - Analog & Digital Outputs 1–4 ..............................4-12
Fig. 4-8: Plug X2 - Serial Interface ...........................................4-13
Fig. 4-9: Conguration of XSTA Terminal Adapter ...............................4-14
Fig. 4-10: Sockets X4.1 and X4.2 - Pin Conguration .............................4-15
Fig. 4-11: Conguration of XSTD Terminal Adapter ...............................4-16
Fig. 4-12: Plug X5 - Analog Inputs ............................................4-17
Fig. 4-13: Conguration of XSTI Terminal Adapter ................................4-18
Fig. 4-14: Power Supply Connectors ..........................................4-19
Fig. 4-15: X-STREAM XEF - Dimensions for Installation...........................4-20
Fig. 4-16: X-STREAM XDF - Dimensions for Installation ..........................4-21
Fig. 4-17: X-STREAM XEXF Field Housings - Terminals, Cable Glands and Gas Fittings .4-22
Fig. 4-18: Terminal Block X1 - Analog Signals and Relay Outputs 1-4 ................4-25
Fig. 4-19: Terminal Block X1 - Serial Interface ...................................4-26
Fig. 4-20: Ethernet Connector ...............................................4-27
Fig. 4-21: X4: Terminal Blocks for Digital Inputs and Outputs........................4-28
Fig. 4-22: Terminal Block X5 - Analog Input Signals ..............................4-29
Fig. 4-23: Power Supply Connections .........................................4-30
Fig. 4-24: Shielded Signal Cable, Shielding Connected At Both Ends. ................4-32
Fig. 4-25: Shielded Signal Cable, Shielding Connected At One end...................4-33
Fig. 4-26: Signal Cable With Double Shielding, Shieldings Connected At Alternate Ends. .4-33
Fig. 4-27: Shield Connector Terminal With Cable.................................4-34
Fig. 4-28: Suppressor Diode for Inductive Loads. ................................4-35
Fig. 4-29: Driving High-Current Loads .........................................4-35
Index of Figures