Endress+Hauser PROline promag 53 - Operating Instructions Manual

164 pages

To Next Page

BA 047D/24/ae/06.01

50103789

Valid as of software version:

V 1.02.XX (amplifier)

V 1.02.XX (communication)

PROline promag 53

Electromagnetic

Flow Measuring System

Operating Instructions

Main Page

Table of Contents5
A F E T y I N S T R U C T I O N S7
Designated Use7
Installation, Commissioning and Operation7
Operational Safety7
Notes on Safety Conventions and Icons8
- 2 I D E N T I F I C a T I O N9
Return8
Device Designation9
- Nameplate of the Transmitter9
- Nameplate of the Sensor10
CE Mark, Declaration of Conformity10
Registered Trademarks11
- I N S T a L L a T I O N13
Incoming Acceptance, Transport and Storage13
- Incoming Acceptance13
- Transport13
- Storage14
Installation Conditions15
- Dimensions15
- Mounting Location15
- Orientation17
- Vibrations18
- Foundations, Supports19
- Adapters20
- Nominal Diameter and Flow Rate20
- Length of Connecting Cable25
Installation Instruction26
- Installing the Promag W Sensor26
- Installing the Promag P Sensor32
- Installing the Promag H Sensor38
- Turning the Transmitter Housing41
- Turning the Local Display42
- Installing the Wall-Mount Transmitter43
- Housing43
Installation Check45
- W I R I N G47
Connecting the Remote Version47
- Connecting Promag W / P / H47
- Cable Specifications51
Connecting the Measuring Unit52
- Connecting the Transmitter52
- Terminal Assignment54
- HART Connection55
Potential Equalization56
- Standard Case56
- Special Cases57
Degree of Protection59
Electrical Connection Check60
- O P E R a T I O61
Display and Operating Elements61
Brief Operating Instruction to the Function Matrix65
- General Notes66
- Enabling the Programming Mode66
- Disabling the Programming Mode66
Error Messages67
Communication (HART)68
- Operating Options69
  - Device and Process Variables70
- Universal / Common Practice HART70
  - Commands70
- Device Status / Error Messages77
- Switching HART Write Protection82
  - On and off82
  - C O M M I S S I O N I N83
Commissioning83
- Switching on the Measuring Device83
- " C O M M I S S I O N I N G " Q U I C K S E T U P M E N U84
- Pulsating Flow" Quick Setup Menu85
- Batching" Quick Setup88
- Empty-Pipe/Full-Pipe Calibration91
- Current Output: Active/Passive92
- Relay Contacts: Normally Closed/Normally Open93
Function Check83
Data Storage Device (DAT, F-Chip™)94
- A C C E S S O R I E97
- T R O U B L E S H O O T I N98
Troubleshooting Instructions99
- System Error Messages100
Process Error Messages105
Process Errors Without Message107
Response of Outputs to Errors109
Spare Parts111
- Boards112
Replacing the Device Fuse116
Replacing Exchangeable Measuring Electrodes117
Software History119
- 0 T E C H N I C a L D a T a121
Technical Data at a Glance121
- Application121
- Function and System Design121
- Input121
- Output122
- Power Supply122
- Performance Characteristics123
- Operating Conditions123
- Mechanical Construction128
- Human Interface132
- 10Certificates and Approvals132
- 11Ordering Information133
- 12Accessories133
- 13Supplementary Documentation133
Measuring Tube Specifications134
Dimensions Wall-Mounted Housing136
Dimensions Promag 53 W137
Dimensions Promag 53 P141
Dimensions of Ground Disks (Promag W, P)146
Dimensions Promag 53 H147
Process Connections Promag H 1/12" to151
- 1-1/2" to 4157

Endress+Hauser PROline promag 53 - Operating Instructions Manual

Table of Contents

Other manuals for Endress+Hauser PROline promag 53

Related product manuals