Endress+Hauser PROline promag 53 - Page 158

10 Technical data PROline Promag 53
158 Endress+Hauser
Process connections with gasket seal (DN 1-1/2" to 4" / 40 - 100)
Weld nipples for ODT pipe
1.4404 / 316L
5*H**-V***********
DN
inch
(mm)
di
inch
(mm)
G
inch
(mm)
D
inch
(mm)
L
inch
(mm)
L1
inch
(mm)
LK
inch
(mm)
1½ (40) 1.39 (35.3) 1.57 (40) 3.62 (92) 1.65 (42) 0.75 (19) 2.79 (71.0)
2 (50) 1.89 (48.1) 2.16 (55) 4.13 (105) 1.65 (42) 0.75 (19) 3.29 (83.5)
2½ (65) 2.36 (59.9) 2.59 (66) 4.76 (121) 1.65 (42) 0.83 (21) 3.94 (100.0)
3 (80) 2.86 (72.6) 3.11 (79) 5.79 (147) 1.65 (42) 0.94 (24) 4.76 (121.0)
4 (100) 3.84 (97.5) 4.09 (104) 6.61 (168) 1.65 (42) 0.94 (24) 5.57 (141.5)
– Fitting length = (2 x L) + 5.51" (1½" - 2½") / + 7.87" (3" - 4")
– Fitting length = (2 x L) + 140 mm (DN 40 - 65) / + 200 mm (DN 80 - 100)
– If pigs are used for cleaning, it is essential to take the inside diameters of measuring tube (Page 149)
and process connection (di) into account.
F06-xxHxxxxx-06-09-07-xx-002
Tri-Clamp
1.4404 / 316L
5*H**-1***********
DN di G D L LK
mm inch inch (mm) inch (mm) inch (mm) inch (mm) inch (mm)
40 1½" 1.37 (34.8) 1.98 (50.4) 3.62 (92) 2.70 (68.6) 2.79 (71.0)
50 2" 1.87 (47.5) 2.52 (63.9) 4.13 (105) 2.70 (68.6) 3.29 (83.5)
65 2½ 2.37 (60.2) 3.05 (77.4) 4.76 (121) 2.70 (68.6) 3.94 (100.0)
80 3" 2.87 (72.9) 3.58 (90.9) 5.79 (147) 2.70 (68.6) 4.76 (121.0)
100 4" 3.83 (97.4) 4.68 (118.9) 6.61 (168) 2.70 (68.6) 5.57 (141.5)
– Fitting length = (2 x L) + 5.51" (1½" - 2½") / + 7.87" (3" - 4")
– Fitting length = (2 x L) + 140 mm (DN 40 - 65) / + 200 mm (DN 80 - 100)
– If pigs are used for cleaning, it is essential to take the inside diameters of measuring tube (Page 149)
and process connection (di) into account.
F06-xxHxxxxx-06-09-07-xx-004