Endress+Hauser PROline promag 53 - Page 30

3 Installation PROline Promag 53
30 Endress+Hauser
Promag W
Nominal diameter
AWWA
Pressure rating
Threaded
fasteners
Max. tightening torque ft-lb (Nm)
[mm] [inch] Hard rubber Polyurethane
700 28" Class D 28 x 1 1/4" 182 (247) 80 (109)
750 30" Class D 28 x 1 1/4 212 (287) 93 (126)
800 32" Class D 28 x 1 1/2" 291 (394) 125 (170)
900 36" Class D 32 x 1 1/2" 309 (419) 137 (186)
1000 40" Class D 36 x 1 1/2" 310 (420) 148 (200)
1050 42" Class D 36 x 1 1/2" 390 (528) 167 (226)
1200 48" Class D 44 x 1 1/2" 407 (552) 177 (240)
1350 54" Class D 44 x 1 3/4" 539 (730) 255 (345)
1500 60" Class D 52 x 1 3/4" 559 (758) 265 (359)
1650 66" Class D 52 x 1 3/4" 698 (946) 322 (436)
1800 72" Class D 60 x 1 3/4" 719 (975) 331 (449)
2000 78" Class D 64 x 2" 629 (853) 407 (552)
Promag W
Nominal diameter
ANSI
Pressure rating
Threaded
fasteners
Max. tightening torque ft-lb (Nm)
[mm] [inch] [lbs] Hard rubber Polyurethane
25 1" Class 150 4 x 1/2"
− 2 (3)
25 1" Class 300 4 x 5/8"
− 6 (8)
40 1 1/2" Class 150 4 x 1/2"
− 4 (6)
40 1 1/2" Class 300 4 x 3/4"
− 15 (20)
50 2" Class 150 4 x 5/8"
− 9 (12)
50 2" Class 300 8 x 5/8"
− 10 (13)
80 3" Class 150 4 x 5/8" 44 (60) 15 (20)
80 3" Class 300 8 x 3/4" 28 (38) 22 (30)
100 4" Class 150 8 x 5/8" 31 (42) 11 (15)
100 4" Class 300 8 x 3/4" 43 (58) 33 (45)
150 6" Class 150 8 x 3/4" 58 (79) 12 (33)
150 6" Class 300 12 x 3/4" 52 (70) 42 (57)
200 8" Class 150 8 x 3/4" 79 (107) 38 (51)
250 10" Class 150 12 x 7/8" 74 (101) 42 (57)
300 12" Class 150 12 x 7/8" 98 (133) 57 (78)
350 14" Class 150 12 x 1" 104 (135) 77 (105)
400 16" Class 150 16 x 1" 94 (128) 75 (102)
450 18" Class 150 16 x 1 1/8" 150 (204) 108 (147)
500 20" Class 150 20 x 1 1/8" 135 (183) 105 (142)
600 24" Class 150 20 x 1 1/4" 198 (268) 161 (218)