Endress+Hauser Proline Prosonic Flow B 200 - Page 152

Index Proline Prosonic Flow B 200 HART
152 Endress+Hauser
Measured variables
Calculated ............................. 130
Direct .................................130
Optional ...............................130
see Process variables
Measuring and test equipment ................ 123
Measuring device
Configuring ............................. 58
Conversion .............................124
Design ................................. 12
Disposal ...............................126
Integrating via HART protocol ................52
Mounting the sensor ...................... 21
Preparing for electrical connection ............ 26
Preparing for mounting .................... 21
Removing ..............................125
Repair ................................ 124
Switch-on .............................. 57
Measuring principle ........................ 130
Measuring range ...........................130
Measuring range, recommended ............... 139
Measuring system ..........................130
Media .....................................9
Menu
Diagnostics ............................ 115
Setup ..................................58
Menus
For measuring device configuration ............58
For specific settings ....................... 84
Mounting dimensions
see Installation dimensions
Mounting location ...........................18
Mounting preparations ....................... 21
Mounting requirements
Installation dimensions .................... 20
Mounting tools ............................. 21
N
Nameplate
Sensor ................................. 15
Transmitter ............................. 14
Navigation path (navigation view) ............... 37
Navigation view
In the submenu .......................... 37
In the wizard ............................ 37
Numeric editor ............................. 39
O
Operable flow range ........................ 131
Operating elements ...................... 41, 108
Operating keys
see Operating elements
Operating menu
Menus, submenus ........................ 34
Structure ............................... 34
Submenus and user roles ................... 35
Operating philosophy ........................ 35
Operation ................................. 97
Operation options ........................... 33
Operational display .......................... 36
Operational safety ...........................10
Order code ...........................13, 14, 15
Orientation (vertical, horizontal) ................ 18
Outlet runs ................................ 19
Output .................................. 132
Output signal ............................. 132
P
Packaging disposal .......................... 17
Parameter
Changing ............................... 45
Enter a value ............................ 45
Parameter settings
Administration (Submenu) .............. 89, 118
Burst configuration 1 to 3 (Submenu) .......... 53
Configuration backup display (Submenu) ....... 90
Current input (Wizard) .....................63
Current output 1 to 2 (Wizard) ............... 65
Data logging (Submenu) ...................102
Device information (Submenu) .............. 119
Diagnostics (Menu) ...................... 115
Display (Submenu) ........................ 87
Display (Wizard) ......................... 78
Low flow cut off (Submenu) ................. 82
Medium selection (Submenu) ................ 62
Operation (Submenu) .....................101
Output conditioning (Wizard) ................80
Output values (Submenu) .................. 100
Process variables (Submenu) .................97
Pulse/frequency/switch output (Wizard) .. 69, 71, 75
Setup (Menu) ............................58
Simulation (Submenu) ..................... 91
System units (Submenu) ....................59
System values (Submenu) ...................99
Totalizer (Submenu) .......................99
Totalizer 1 to 3 (Submenu) .................. 85
Performance characteristics ...................136
Post-connection check (checklist) ............... 32
Post-installation check ....................... 57
Post-mounting check (checklist) ................ 23
Potential equalization ........................ 28
Power consumption .........................135
Power supply failure ........................ 135
Pressure Equipment Directive ................. 147
Pressure loss ..............................139
Pressure-temperature ratings ................. 139
Process connections ........................ 143
Product safety ..............................10
Protecting parameter settings .................. 94
R
Read access ................................46
Reading measured values ......................97
Recalibration ..............................123
Reference operating conditions ................ 136
Registered trademarks .........................8
Remedial measures
Calling up ............................. 109