746 C - 844 C 44 532150 - Rev.A
Translation of the original instructions
ENGLISH
INSTALLING THE XF FDS OR XF RADIO
MODULE
1. The module should only be inserted into the con-
nector with the board turned off and as indicated
in the figure.
2. Only switch on power supply after having installed
the module. Then memorise the radio controls.
i
Follow the instructions to memorise the radio controls
according to their type.
Carry out the procedure with the radio control approxi-
mately 1 m away from the board.
MEMORISING XF FDS RADIO CONTROLS
1. On the board, press the ++ (memorise OPEN
A) or
--
(memorise OPEN B/CLOSE) button and
release it when the corresponding RADIO LED
(RADIO1 or RADIO2) starts to flash for 20 s (time
available for the next step).
2. Press and release the button on the radio control
that you wish to memorise for the radio chan-
nel. To confirm the memorisation, the RADIO
LED lights up steadily for 2 s and then starts to flash
again for another 20 s (time available to repeat step
2 on another radio control).
The procedure ends after 20 s if no further radio
controls are memorised and the RADIO LED switches
off. To add additional radio controls, repeat the pro-
cedure from step 1.
MEMORISING SLH/SLH LR RADIO CONTROLS
Memorise the first Master radio control on the bo-
ard. Afterwards, it is not necessary to access the
board in order to add radio controls.
To check if the radio control is a Master device, press
and hold a button and watch the LED:
- flashes briefly, then the light becomes stea-
dy = Master
- turns on immediately with a steady light = NON
Master
i
Whenever a new Master is memorised on the board,
any SLH/SLH LR radio controls that are already in use
are disabled.
■ Memorising the first radio control (Master)
1. On the board, press the
++ (memorise OPEN A) or
--
(memorise OPEN B/CLOSE) button and release it
when the corresponding RADIO LED (RADIO1 or
RADIO2) starts to flash for 20 s (time available for
the next steps).
2. Press buttons P1 and P2 simultaneously on the
radio control and release them when LED on the
radio control starts to flash for 8 s (time available
for the next step).
3. Press and release the button on the radio control to
be memorised. The corresponding RADIO LED on
the board becomes steady for 1 s and then switches
off (memorisation complete).
4. Release the button.
When using the memorised button for the first time,
press it twice in succession to obtain the command.
■ Adding SLH/SLH LR radio controls
1. Press buttons P1 and P2 simultaneously on the
already memorised Master radio control and rele-
ase them when its LED on the radio control starts
to flash for 8 s (time available for the next step).
2. Within 8 s, press and hold the button that has
already been memorised, the LED lights up with
a steady light.
3. Bring the radio control that has already been me-
morised, into contact face to face with the new one
to be memorised.
4. Press and release the button on the new radio con-
trol to be memorised. The LED of the radio control
flashes twice and then switches off (memorisation
complete).
5. Release the buttons.
When using the memorised button for the first time,
press it twice in succession to obtain the command.
MEMORISING LC/RC RADIO CONTROLS
1. On the board, press the ++ (memorise OPEN A) or
--
(memorise OPEN B/CLOSE) button and release it
when the corresponding RADIO LED (RADIO1 or
RADIO2) starts to flash for 20 s (time available for
the next steps).
2. Press and release the button on the radio control
to be memorised. The corresponding RADIO LED
on the board becomes steady for 2 s (memorisation
completed), then starts to flash again. Another
radio control can be memorised within 20 s.
The procedure ends after 20 s if no further radio
controls are memorised and the RADIO LED switches
off. To add additional radio controls, repeat the
procedure from step 1.
■ Adding LC/RC radio controls
Use a LC/RC radio control that is already use by the
automation, without having to use the board.
To Next Page
Loading...
