Fargo DTC300 - Page 115

RESTRICTED USE ONLY Fargo Electronics, Inc.
DTC300/DTC300M Card Printer/Encoder User Guide (Rev. 2.2)
5-2
Using the Magnetic Track Selection radio buttons_______________________________________ 5-45
Using the Magnetic Track Selection radio buttons (continued)___________________________ 5-46
Using the Magnetic Track Options radio buttons________________________________________ 5-47
Using the Bit Density radio buttons __________________________________________________ 5-48
Using the Character Size radio buttons________________________________________________ 5-49
Reviewing the Enable MLE Support checkbox _________________________________________ 5-50
Using the ASCII Offset radio buttons_________________________________________________ 5-51
Using the LRC Generation radio buttons ______________________________________________ 5-52
Using the Character Parity radio buttons ______________________________________________ 5-52
Using the Shift Data Left checkbox __________________________________________________ 5-53
Reviewing the ISO Track Locations__________________________________________________ 5-54
Sending the Track Information______________________________________________________ 5-55
Entering the Track Information _____________________________________________________ 5-55
Reviewing Tracks 1, 2 and 3 (in table format) __________________________________________ 5-56
Reviewing the Track Data Note _____________________________________________________ 5-56
Reviewing the ASCII Code and Character Table________________________________________ 5-57
Using the Overlay / Print Area tab _____________________________________________________ 5-58
Using the Overlay / Print Area dropdown menu ________________________________________ 5-59
Using the Overlay / Print Area dropdown menu (continued) ____________________________ 5-60
Using the Overlay / Print Area ______________________________________________________ 5-61
Using the Overlay / Print Area (continued) __________________________________________ 5-62
Using the Defined Area Option _____________________________________________________ 5-63
Using the Defined Area Option (continued) _________________________________________ 5-64
Using the Defined Area Option (continued) _________________________________________ 5-65
Using the Defined Area Option (continued) _________________________________________ 5-66
Using the Defined Area Option (continued) _________________________________________ 5-67
Using Security Options (Visual Security Solutions)______________________________________ 5-68
Selecting Orientation - Landscape under Card tab _______________________________________ 5-69
Selecting the Visual Security Solutions dropdown menu (A to D) __________________________ 5-70
Selecting Orientation - Portrait under Card tab _________________________________________ 5-71
Selecting the Visual Security Solutions dropdown menu (E to H)___________________________ 5-72
Selecting the VeriMark radio button _________________________________________________ 5-73
Selecting the HoloMark radio button _________________________________________________ 5-74
Reviewing the Custom VeriMark Card (Custom Graphic in a 2D foil) _______________________ 5-75
Sample 1: VeriMark Card (Landscape - Orientation) - 4 positions (below) _________________ 5-75
Sample 2: VeriMark Card (Portrait - Orientation) - 4 positions (below)____________________ 5-75
Reviewing the Custom HoloMark Card (Custom Graphic in a 2D foil) ______________________ 5-76
Sample 1: HoloMark Card (Landscape - Orientation) - 4 positions (below)_________________ 5-76
Sample 2: HoloMark Card (Portrait - Orientation) - 4 positions (below) ___________________ 5-76
Using the K Panel Resin tab __________________________________________________________ 5-77
Selecting from the Print All Black With K Panel options _________________________________ 5-78
Selecting the Full Card option ______________________________________________________ 5-79
Selecting the Defined Area(s) option _________________________________________________ 5-80
Selecting the Undefined Area(s) option _______________________________________________ 5-81
Selecting the Defined Area(s) function _______________________________________________ 5-82
Selecting the Defined Area(s) function (continued) ___________________________________ 5-83
Selecting the Defined Area(s) function (continued) ___________________________________ 5-84
Selecting the Defined Area(s) function (continued) ___________________________________ 5-85
Selecting the Defined Area(s) function (continued) ___________________________________ 5-86
Selecting the Defined Area(s) function (continued) ___________________________________ 5-87
Selecting the Defined Area(s) function (continued) ___________________________________ 5-88
Selecting the Print YMC under K and Print K Only options _______________________________ 5-89
Using the Printer Supplies tab_________________________________________________________ 5-90
Reviewing the Ribbon Information __________________________________________________ 5-91
Reviewing the Ribbon Level Indicator________________________________________________ 5-92
Using the Printer Calibration Utility ____________________________________________________ 5-93