Fargo DTC300 - Page 271

RESTRICTED USE ONLY Fargo Electronics, Inc.
DTC300/DTC300M Card Printer/Encoder User Guide (Rev. 2.2) 14-3
Input Hopper, 13-10
integral resistor, 6-2
Interface, 2-3
Intermediate Transfer Media (InTM), 13-10
internal electrical components, 6-2
internal Printer settings, 5-39
ISO, 13-10
ISO 7811-2 Magnetic Stripe, 5-54
ISO encoded data format, 5-47
ISO Standard selections, 5-52
ISO Standard settings, 5-45
ISO Track Locations, 5-54
J
JIS II (Japanese Industrial Standard), 13-10
K
K Panel, 13-10
K Panel Resin options, 5-67, 5-88
K Panel Resin tab, 5-78
L
Lamination, 13-10
Lamination Drive, 8-2
Lamination Drive Stepper, 8-2
Lamination Roller Lift, 8-2
Lamination Sensor Calibration, 4-54
LAN (Local Area Network), 13-10
Landscape, 13-11
Landscape orientation, 5-40
LCD (Liquid Crystal Display), 13-11
LED (Light Emitting Diode), 13-11
less heat / more heat, 5-33, 5-34, 5-36, 5-37
LoCo (Low Coercivity), 13-11
LPT Port (Line Printer Port), 13-11
LRC Generation, 5-52
LRC Generation Mode, 5-52
M
magnetic data, 5-101
Magnetic Encoder, 4-18
Magnetic encoding, 13-11
Magnetic Offset option, 5-101
Magnetic Offset value, 5-101
Magnetic stripe, 13-11
, 4-15
Magnetic Stripe Encoding Module, 5-44
Magnetic Stripe reader, 4-15
Magnetic Track, 13-11
Magnetic Track Options, 5-45
Magnetic Track Selection, 5-45, 5-46
Magnetic Track Selection option, 5-45
Magnetic Verify, 13-11
maximum adjustment range, 5-96, 5-101
MB (Megabyte), 13-12
Media, 13-11
Memory, 2-3, 13-12
Menu, 13-12
Metallic Resin, 2-10
Monitor, 5-20
Monochrome, 13-12
Monochrome Dye-Sub (B), 4-54
Monochrome Resin (K), 4-54
Motor Voltages (when active), 8-2
Multi-Language Extension (MLE), 5-50
N
Network, 13-12
None, 5-20
O
Oersted (Oe), 13-12
Offset, 13-12
Omit Signature Area setting, 5-64
On LED, 4-54, 4-55
onscreen card design, 5-84
Operating Temperature, 2-3
optional Magnetic Stripe Encoding Module, 5-44
O-Ring, 13-12
OS (Operating System), 13-12
Output, 13-12
Output Hopper, 13-12
Overlaminate, 13-13
Overlay, 13-12
Overlay / Print Area, 5-64, 5-65
Overlay / Print Area options, 5-61
Overlay / Print Area tab, 5-58
Oversized Cards, 13-13
P
Parallel, 13-13
Parallel port, 13-13
Pause button and LED, 2-8
Pause/Resume button, 4-54, 4-55
PC (Personal Computer), 13-13
PCB (Printed Circuit Board), 13-13
Peel, 13-13
Peel-Off, 13-13
Peripheral, 13-13
PET, 13-14
Photo, 5-21, 5-30
Pinch Roller, 13-14
Pixel, 13-14
, 4-41
Platen, 13-14
PolyGuard Overlaminate, 13-14
poor image quality problems, 4-51, 4-52
Port, 13-14
Portrait, 13-14
Portrait or Landscape, 5-8
Portrait, Landscape, or Rotate 180 Degrees, 5-40
positive / negative Print Length value, 5-96
POSITIVE / NEGATIVE value., 5-95
Potentiometer, 13-14
Power Port, 2-8
power/data cables, 4-36