RESTRICTED USE ONLY Fargo Electronics, Inc.
DTC400 Card Printer/Encoder User Guide (Rev. 2.2) 2
Section 15: Index
A
About button, 6-13
AC - Alternating Current, 14-1
Accepted Card Thickness, 2-2
Accepted Card Types, 2-2
Accepted Standard Card Sizes, 2-2
Access Card, 14-1
Adhesion, 14-1
Adjusting the Image Darkness, 4-44, 4-46
Agency Listings, 2-2
Algebraic, 6-19, 14-1
ANSI (American National Standards Institute), 14-1
AS400, 14-1
ASCII (American Standard Code for Information
Interchange), 14-1
ASCII Code, 6-48
ASCII Offset, 6-43
AT, 14-1
automated Flipping Module, 2-14
B
B (Black), 14-1
Barcodes, 14-2
Batch print, 14-2
Battery Back-up, 14-2
Bi-directional, 14-2
BIOS (Basic Input/Output System), 14-2
Bit, 14-2
Bit Density, 6-40
Bit map, 14-2
blocked Sensor, 4-33
Board, 14-2
Boot-up, 14-2
Buffer, 14-2
C
Cable, 14-2
Cache, 14-3
Calibrate tab, 4-36, 4-50, 6-31
Calibrating, 14-3
Cancel button, 2-8
Card Cleaning Roller, 2-8
Card Design, 2-13
Card Feeding Errors, 4-10, 4-12, 4-15, 4-16, 4-18, 4-
20, 4-22, 4-25, 4-27, 4-29, 4-31, 4-33
card grid, 6-59
card grid area, 6-58
card grid lines, 6-60
card input, 6-93
Card Input Hopper, 2-8
Card Input Hopper Capacity, 2-2
card orientation, 6-61
card output, 6-93
Card Size, 2-13
card stock scratches, 4-41
Card Surface, 2-13
cards look pixilated or grainy, 4-53
card's Magnetic Stripe/smart chip, 6-25
CD (Compact Disc), 14-3
Centronics, 14-3
Character, 6-48
Character ASCII Offset, 6-43
Character Parity, 6-44
Character Size radio buttons, 6-41
Cleaning Card Feed/Cleaning Rollers, 7-4
Cleaning Cards, 7-2
Cleaning Inside Printer, 4-42
Cleaning Pad, 7-5
Cleaning Pads, 7-2
Cleaning Printer's Interior, 7-5
Cleaning Roller, 14-3
Cleaning the Printhead, 4-41
Clear Protective Overlay Panel, 2-9
Coercivity, 14-3
Color matching, 14-3
Color Matching, 6-19
Color Matching software, 6-19
Colored Resin, 2-10
Colors, 2-2
Communication Errors, 4-4, 4-5
Compressed air, 14-3
Contrast, 14-3
Contrast / Gamma, printed image, 6-27
Control panel, 14-3
CR-100, 14-4
CR-79, 14-4
CR-80, 14-4
CR-80 card size, front/back, 6-77, 6-78, 6-79
CR-90, 14-4
CSA, 2-1
Cursor, 14-4
customized ID software applications, 6-47
D
Darkness, 14-4
Data Cables, 4-36
DB-9, 14-4
DC (Direct Current), 14-4
DC Motor, 14-4
Default, 14-4
Default button, 6-30, 6-37
default ISO Standard selections, 6-40, 6-44
default location, 6-81
defined area, 6-61
Defined Area arrows, 6-62
Defined area(s), 6-80
Defined Area(s) check box, 6-80, 6-81, 6-82, 6-86, 6-87,
6-89, 6-90, 6-95, 6-97, 6-98, 6-101
Defined Area(s) option, 6-54, 6-59, 6-78
Defined/undefined area(s), 6-77, 6-79
Defrag, 14-4
To Next Page
Loading...
