+
Receiver will be used for backup only; not checked.
Ø
Local Port and Remote Port – These values repre
-
sent the ports to be used for communication with the
backup receiver. Default values: 3065 (Local Port)
and 3066 (Remote Port).
Third
Ø
Receiver IP – This is the IP address assigned to the
receiver of the domotics system with which you wish
to interact. It is supplied by the receiver itself. Default
value: 40000.
Local Port and Remote Port – These values represent
the ports to be used when communicating with the do
-
motics system receiver. They are supplied by the recei
-
ver itself. Default value: 40001.
The receiver will be used for the domotics system only;
not checked.
ADVANCED
LED Trouble mask / Output Trouble mask.
This section can be used to enable/disable signals from
the OC output and the indicator light , for certain events
recognised by the IP Module: Network Absent.
A tick indicates that the corresponding event will be si
-
gnalled! The LAN not detected event indication is ena
-
bled by default.
Output polarity. This section is used to set the
operating mode of the OC output on the IP Module.
Ø Open on trouble – The outlet is suspended when a
breakdown occurs (default setting).
Ø Close on trouble – The output is connected to the
earthing system when a breakdown occurs.
For the IP module, the procedure to “restore to the
factory defaults” , use the icon in the Advanced
section. In the same section, Advanced, can be fo-
und the button to upgrade the firmware and the
button to reset the FC500IP board.
For an explanation of the further parameters and the
programming, see the dedicated manual of the
FC500IP module.
Events
In this section , for each event recognized
by the Panel, it is possible to program: the telephone
numbers to call, the Voice Message and the Events
code to be sent. The Alarm, Prealarm, Warning, Fault
and Walk Test events can be sent to up to 32 telephone
numbers . The telephone numbers are set in the
ADDRESS BOOK section . It is also possible to set
the type of phone call: Voice or Telemonitoring
or for IP communicator .
There are these options to use the voice messages:
1)- record them directly on PC or import present messa
-
ges on PC using the functionality of the buttons in the
Messages section;
2)- first: importing them on PC from an external source,
a USB stick, second: upload them, using the functiona
-
lity of the buttons in the Messages section.
+
To load the voice messages in the Panel it is ne
-
cessary to use the USB connector on the mother
-
board and to start the Programming procedure of
the Panel by User Interface (see Programming
from the Panel, 7 KEY -USB-.
CLOCK
The Date/Time option from the CLOCK menu is for the
control panel clock settings.
Enter the required Time and Date.
Schedule the automatic application of summer time if
required. The button will change the daylight sa
-
ving to the default values.
LOG
This option allows to read the Log stores events.
Description of the icons in the LOG bar:
Up load from Board: click on this icon to upload the
LOG of the connected control panel.
Export LOG to file: click on this icon to export the
LOG in a (*.fcl) or (*.xml) or (*.xmc) file.
Import LOG from file: click on this icon to import the
LOG from a (*.fcl) or (*.xml) or (*.xmc) file.
Apply filter: click on this icon to select the LOG fil-
ter (if necessary):
Ø Enabled/Disabled/Restore/Alarm/Prealarm/Warning
/Fault/Generic/Walk test
If required set other filters for the Event Log:
Ø Filter by panel/Filter by Loop/Filter by device /Filter
by zone.
Print a text file; in this case the control panel Event
Log, or part of it.
The following data will be stored in the LOG: the Event’s
Number, the Date, the Time, the Class (Fault, Alarm,
Warning, Generic and Walk test), the Event’s descrip
-
tion, the Control panel number, the Loop, the Device
type, the Status, the Threshold and the Zone.
Clicking on this icon will delete the Event Log.
UTILITIES
In the Utilities page, it is possible:
shows the calculation of the batteries (see next de
-
dicated paragraph );
enable a USB stick both to load the firmware, voice
messages, panel programming, then download
the data of a customer;
+
Clicking on "Overrride" now it is possible to chan
-
ge the panel ID for export/import, and if also the
option "Any Panel [XXXX]" is implemented it is pos
-
sible to utilize this configuration in any Panel (e.g.
to load same voice messages in several panels)
Load the label of the first 8 zones, which should be
printed and inserted in the transparent window in the
40 Addressable Fire Panel FC501
To Next Page
Loading...
