ACCESSORY
The following is a list of accessories for FC501 control
panel, with a description of the main features. For fur
-
ther information about these accessories, please refer
to the instructions supplied with the accessories them
-
selves or download them from the website: web:
http://www.fireclass.net.
FC500IP - IP Module
The FC500IP is an IP Module which is used to connect
the FC501 fire panel to a LAN.
The IP Module may be connected to a LAN using a pri
-
vate IP address or a DHCP address.
The same procedures may be performed using the FireC
-
lass console application, either through the serial port or
the network. With a public IP address, it is also possible to
manage and monitor the control panel from anywhere in
the world, as long as you have access to the Internet.
4B - Universal Base
The 4B Universal base is for use with the
FC460/FC400/600 series of detectors.
The base may be fixed directly to:
Ø British (fixing centres 50mm) or European (fixing
centres 70mm) conduit box;
Ø 4B EM Euro Mounting Box;
Ø the suspended ceiling, through the CTA adapter;
Ø directly to the ceiling.
FC460H or FC400H-Addressable Heat Detector
The detector is intended to plug into the following:
Ø
4B 4” Universal Base
Ø
4B-I 4” Isolator Base
Ø
FC430SB Low Power Sounder Base
Ø
FC430LPSB Loop Powered Addressable Sounder
Base.
Ø
FC430LPASB Loop Powered Addressable Soun
-
der/Beacon Base.
Software within the controller is used to interpret the re
-
turned heat values to raise an alarm or other appropria
-
te response according to the type of detector configured
in Fire Class Console.
The mode of detector may be:
Ø
EN54-5 A1R, rate-of-rise normal ambient
Ø
EN54-5 A2S, fixed 60
o
C
Ø
EN54-5 CR, rate-of-rise high ambient..
FC460P or FC400P - Addressable Optical
Smoke
The FC460P/FC400P optical smoke detector forms
part of the FC460/FC400 Series Addressable Fire de
-
tectors.
Ø
4BI 4”Isolator Base
Ø
4B 4” Universal Base
Ø
FC430SB Low Power Sounder Base
Ø
FC430LPSB Loop Powered Addressable Sounder
Base.
Ø
FC430LPASB Loop Powered Addressable Soun
-
der/Beacon Base.
Software within the controller is used to interpret the re
-
turned optical and heat values to raise alarm or other
appropriate response according to the type of detector
configured in Fire Class Console.
FC460PH or FC400PH - Addressable
Optical Smoke & Heat Detector
The detector is intended to plug into one of the following:
Ø 4B 4” Universal Base
Ø
4B-I 4” Isolator Base
Ø
FC430SB Low Power Sounder Base
Ø
FC430LPSB Loop Powered Addressable Sounder
Base.
Ø FC430LPASB Loop Powered Addressable Soun-
der/Beacon Base.
Software within the controller is used to interpret the returned
optical and heat values to raise alarm or other appropriate
response according to the type of detector configured in Fire
Class Console. The mode of detector may be:
Ø
Mode 1 - Optical smoke only detector (sensitivity
High, Normal or Low)
Ø
Mode 2 - Optical ( sensitivity High, Normal or Low )
and heat fixed temperature 60
o
C (A2S)
Ø
Mode 3 - Heat only rate-of-rise (A1R) detector (no
sensitivity selection)
Ø
Mode 4 - Heat fixed temperature 60
o
C (A2S) (no sen
-
sitivity selection)
Ø
Mode 5 - Heat rate-of-rise (A1R) detector and optical
smoke (sensitivity High, Normal or Low)
Ø
Mode 6 - HPO (Advanced) smoke detector (sensivity
High, Normal or Low)
Ø
Mode 7 - HPO (Advanced) and heat fixed temperatu
-
re 60
o
C (A2S)
Ø
Mode 8 - HPO (Advanced) and heat rate-of-rise (A1R).
ACCESSORY 63
To Next Page
Loading...
