458
Index
D
Data input ... 353
Data output ... 353
Deactivate zero-point shifts
G920 ... 351
Deactivate zero-point shifts, tool
lengths G921 ... 352
Deburring G840 ... 334
Deep-hole drilling G74 ... 299
Dialog texts for subprograms ... 368
DIN PLUS workpiece blank
definition ... 180
DIN/ISO programs, converting ... 177
Drilling and boring cycles
DIN programming ... 292
Drilling and boring cycles, overview and
contour reference... ... 292
Drilling cycle G71 ... 293
Drilling pattern, circular, face
G745 ... 303
Drilling pattern, circular, lateral surface
G746 ... 305
Drilling pattern, linear, face G743 ... 302
Drilling pattern, linear, lateral surface
G744 ... 304
Drilling, deep-hole drilling G74 ... 299
E
Eccentric polygon in XY plane G377-
Geo ... 393
Eccentric polygon in YZ plane G387-
Geo ... 401
Eccentric polygon on front/rear face
G307-Geo ... 213
Eccentric polygon on lateral surface
G317-Geo ... 222
Elements of a DIN/ISO program ... 26
END (section code) ... 39
Engraving in the YZ plane G804 ... 424
Engraving in XY plane G803 ... 423
Engraving on front face G801 ... 346
Engraving on lateral surface
G802 ... 347
Engraving, character set ... 345
Example
Fixed cycle programming ... 175
Machining with the Y axis ... 427
Subprogram with contour
repetitions ... 380
Expert programs ... 176
F
Face roughing G820 ... 249
Face roughing, simple... G82 ... 374
Feed per minute G94 ... 231
Feed per revolution G95 ... 231
Feed per revolution G95-Geo ... 200
Feed per revolution Gx95 ... 231
Feed per tooth Gx93 ... 231
Feed rate ... 230
Feed rate override 100% G908 ... 351
Feed rate reduction G38-
Geo ... 198, 199
Feed rate, interrupted G64 ... 230
Figure milling cycle, face G793 ... 319
Figure milling cycle, lateral surface
G794 ... 321
File organization, smart.Turn
editor ... 35
Finish contour G890 ... 262
Finishing
DIN PLUS
Cycle G890 ... 262
Fixed cycle programming (DIN
PLUS) ... 175
Front face contours ... 207
Front face machining ... 309
Full circle in XY plane G374-Geo ... 392
Full circle in YZ plane G384-Geo ... 400
Full circle on face G304-Geo ... 212
Full circle on lateral surface G314-
Geo ... 221
G
G functions for contour description
G0 starting point of turning
contour ... 181
G1 line segment in a contour ... 182
G100 Starting point of front/rear
face contour ... 207
G101 Line segment in front/rear
face contour ... 208
G102 Circular arc in front/rear face
contour ... 209
G103 Circular arc in front/rear face
contour ... 209
G110 Starting point of lateral surface
contour ... 216
G111 Line segment in a lateral
surface contour ... 217
G112 Circular arc in lateral surface
contour ... 218
G113 Circular arc in lateral surface
contour ... 218
G12 circular arc in a contour ... 184
G13 circular arc in a contour ... 184
G149 Additive compensation ... 201
G170 Starting point of contour in XY
plane ... 388
G171 Line segment in XY
plane ... 388
G172 Circular arc in XY plane ... 389
G173 Circular arc in XY plane ... 389
G180 Starting point of contour in YZ
plane ... 397
G181 Line segment in YZ
plane ... 397
G182 Circular arc in YZ plane ... 398
G183 Circular arc in YZ plane ... 398
G2 circular arc in a contour ... 183
G20 Chuck part: cylinder/
tube ... 180
G21 cast part ... 180, 349
G22 recess (standard) ... 185
G23 Recess (general) ... 187
G24 thread with undercut ... 189
G25 Undercut contour ... 190, 371
G3 circular arc in a contour ... 183
G300 Bore hole on front/rear
face ... 210
G301 Linear slot on front/rear
face ... 211
G302 Circular slot on front/rear
face ... 211
G303 Circular slot on front/rear
face ... 211
G304 Full circle on front/rear
face ... 212
G305 Rectangle on front/rear
face ... 212
G307 Eccentric polygon on front/
rear face ... 213
G308 Start pocket/island ... 202
G309 End of pocket/island ... 202
G310 Bore hole on lateral
surface ... 219
G311 Linear slot, lateral
surface ... 220
G312 Circular slot on lateral
surface ... 220
G313 Circular slot on lateral
surface ... 220
G314 Full circle, lateral
surface ... 221
G315 Rectangle, lateral
surface ... 221
To Next Page
Loading...
Need help?
General
