HEIDENHAIN MANUALPLUS 620 User Manual

462
Index
Recessing, recessing cycle G870 ... 261
Recessing, repeat recessing cycle
G740/G741 ... 257
Rectangle in XY plane G375-Geo ... 393
Rectangle in YZ plane G385-Geo ... 401
Rectangle on face G305-Geo ... 212
Rectangle on lateral surface G315-
Geo ... 221
Reference diameter G120 ... 307
Repeat recessing cycle G740/
G741 ... 257
Replacement tools ... 43
RETURN (section code) ... 39
Rotary axes ... 26
Roughing, contour-parallel
(G830) ... 251
Roughing, contour-parallel with neutral
tool G835 ... 253
Roughing, face G820 ... 249
Roughing, longitudinal G810 ... 247
Run-out length (thread) ... 271
S
Safety clearance, milling cycles,
G147 ... 241
Safety clearance, turning cycles,
G47 ... 241
Screen layout, smart.Turn editor ... 29
Section codes, CONST... ... 40
Section codes, END... ... 39
Section codes, RETURN... ... 39
Section codes, VAR... ... 40
Sections, AUXIL_BLANK... ... 38
Sections, AUXIL_CONTOUR... ... 38
Sections, BLANK... ... 38
Sections, FACE_Y... ... 39
Sections, FACE... ... 38
Sections, FINISHED... ... 38
Sections, HEADER... ... 37
Sections, LATERAL_Y... ... 39
Sections, LATERAL... ... 38
Sections, MACHINING... ... 39
Sections, REAR_Y... ... 39
Sections, REAR... ... 38
Sections, SUBPROGRAM... ... 39
Sections, TURRET... ... 37
Shaft speed ... 230
Simple turning cycles ... 373
Simplified geometry
programming ... 174
Single surface in XY plane G376-
Geo ... 396
Single surface in YZ plane G386-
Geo ... 404
Single thread G32 ... 276
Slot, circular, lateral surface G312/
G313-Geo ... 220
Slot, circular, on face G302/G303-
Geo ... 211
Slot, linear, face G791 ... 317
Slot, linear, lateral surface G311-
Geo ... 220
Slot, linear, lateral surface G792 ... 318
smart.Turn editor ... 28
smart.Turn editor, menu structure ... 28
Speed Gx97 ... 232
Speed limitation G26 ... 230
Spindle override 100% G919 ... 351
Standardize C axis G153 ... 308
Start pocket/island G308-Geo ... 202
Starting length (thread) ... 271
Starting point of contour in XY plane
G170-Geo ... 388
Starting point of contour in YZ plane
G180-Geo ... 397
Starting point of face contour G100-
Geo ... 207
Starting point of lateral surface contour
G110-Geo ... 216
Starting point of turning contour G0-
Geo ... 181
Structured NC program ... 25
Subprogram call: L"xx" V1 ... 367
Subprogram, dialogs texts in
subprogram call ... 368
Subprogram, help graphics for
subprogram calls ... 368
Subprograms—Fundamentals ... 176
Switch off protection zone G60 ... 350
SWITCH..CASE—program
branching ... 366
T
T command ... 242
T command, fundamentals ... 41
Tapered API thread G352 ... 281
Tapping G36—Single path ... 298
Tapping G73 ... 296
Thread (general) G37-Geo ... 195
Thread (standard) G34-Geo ... 194
Thread cycle G31 ... 272
Thread cycle, single G32 ... 276
Thread cycles ... 271
Thread milling in XY plane G800 ... 425
Thread milling in YZ plane G806 ... 426
Thread milling, axial G799 ... 306
Thread overrun ... 271
Thread single path G33 ... 278
Thread with undercut G24-Geo ... 189
Thread, metric ISO... G35 ... 280
Thread, tapered API... G352 ... 281
Tilted position of tool carrier ... 41
Tool call T ... 242
Tool change point, moving
to...G14 ... 226
Tool commands ... 242
Tool data, reading... ... 357
Tool entries, editing... ... 42
Tool form ... 47
Tool list, setting up... ... 41
Tool positioning in the Y axis ... 406
Tool programming ... 41
Tool, positioning... ... 225
Tool-change point,
definition...G140 ... 226
Tool-tip radius compensation ... 233
TRC, switch off... G40 ... 233
TRC, switch on... G41/G42 ... 234
Turning cycles, contour-based... ... 246
Turning cycles, simple... ... 373
U
Undercut ... 371
Undercut according to DIN 509 E with
cylinder machining G851 ... 286
Undercut according to DIN 509 F with
cylinder machining G852 ... 287
Undercut according to DIN 76 with
cylinder machining G853 ... 288
Undercut contour G25 ... 371
Undercut contour G25-Geo ... 190
Undercut Cycle G85 ... 284
Undercut cycles ... 284
Undercut DIN 509 E ... 191
Undercut DIN 509 F ... 191
Undercut DIN 76 ... 192
Undercut G85 ... 284
Undercut type H ... 192
Undercut type H G857 ... 290
Undercut type K ... 193
Undercut type K G858 ... 291
Undercut type U ... 190
Undercut type U G856 ... 289
Unit "API thread" ... 106
Unit "Bidirectional roughing in ICP" ... 55
Unit "C axis OFF" ... 139
Unit "C axis ON" ... 139
Unit "Centric drilling" ... 64

HEIDENHAIN MANUALPLUS 620 Specifications

General

Brand	HEIDENHAIN
Model	MANUALPLUS 620
Category	Control Systems
Language	English