56Honeywell, Issue 9
March 2007
XLS80e Fire Alarm Control Panels
7.2 Input Categories
Valid inputs are shown below.
CONTROL MATRIX INPUTS
EXTING-
UISHING (b)
D
Select
System
Before/
after
delay
(a) Additional option 'Remote Fire Output Disabled' is available if such
an output is configured.
(b) These inputs do not latch the outputs, i.e. output returns to normal
when cause of its action is removed. Also applies to individual AUX
modules.All other control matrix actions are latching.
(c) If 2-Devices Coincidence and Restricted-by-type are both selected,
the type check is carried out on the second activated device (the
one which completes the coincidence). The first device may therefore
be of a different type. It is best to avoid this combination and place all
devices to be included in the coincidence into a specific zone or cell.
3-devices or more: type check applies to .
(d) This input determines the action taken if any MCP is activated in walk
test. If there is no entry of this type, the action taken will be that
determined by the control matrix entry for the MCP device. In either
case, actions apply only at the local panel except in the case where
both an MCP in walk test entry and an XLSnet are configured.
(e) If the panel is on a network, this input can be from a specific panel,
remaining OTHER inputs are from any panel.
(f) The use of zone coincidence and type restriction in the same control
matrix entry is not supported.
(g) XLS
only
all
net only: If enabled in Network Panel Settings, Transfer Flag can
be from a remote panel.
Note: If the panel is on a network, an additional selection of 'fallback'is
given after the panel selection is made.
ALARM (Multi-criteria/
MCS in Normal mode)
PRE-ALARM
CELL, ZONE
OR PANEL
SPECIFIED
DEVICE
INPUT FROM
SPECIFIED
ZONES
INPUT FROM
ANY ZONE
CELL
ZONE/
PANEL
Select
Panel &
Zone(s)
Zone
Coincidence
(available only if
input is ALARM
and more than one
zone is selected) (f)
Restricted-
by-type (f)
Select
Cell(s)
Device Coincidence
(if no zone
coincidence &
dependent upon
the restricted-by-type
selection. Pre-alarm and
cell: only 2-device
coincidence available) (c)
A
B
Sensor/
Module
Select
Device
IF INPUT IS
ALARM
IF INPUT IS
PRE-ALARM
Select
Zone
Select
Device
VIRTUAL
INPUT
POINT
Select
Point
OTHER (b)
EVACUATE (e)
RESET
SILENCE
MCP IN
WALK
TEST (d)
TRUE
TRANSFER
FLAG
B
Specify
Panel
Any
Panel
Select
Flag (g)
D
E
NON-FIRE (b)
CELL, ZONE
OR PANEL
INPUT FROM
SPECIFIED
ZONES
INPUT
FROM
ANY ZONE
CELL
ZONE/
PANEL
Select
Panel &
Zone(s)
Select
Cell(s)
C
SPECIFIED
DEVICE
Select
Zone
Select
Device
PANEL
INPUT 1
PANEL
INPUT 2
XLSnet only:
Specify
Panel
VIRTUAL
INPUT
POINT
Select
Point
DISABLEMENT (a) (b)
ZONE GENERAL
PANEL
SOUND-
ERS
B
Select
Zone(s)
VIRTUAL
INPUT
POINT**
Select
Point
** This option is
not yet available
FAULT
B
ZONE GENERAL
PANEL
INPUT
FROM
SPECIFIED
ZONES
INPUT
FROM
ANY
ZONE
Select
Panel &
Zone(s)
VIRTUAL
INPUT
POINT**
Select
Point
Select
Panel &
Zone(s)
Select
Device
2-Devices
coincidence
A
ALARM
Multi-criteria/MCS
Alarm Mode
Normal
(Combined)
Thermal-only
Z
Z
To Next Page
Loading...
