HP 5120 EI Series

185
[PE1-GigabitEthernet1/0/1] port hybrid vlan 10 20 tagged
[PE1-GigabitEthernet1/0/1] port hybrid vlan 100 200 untagged
# Enable basic QinQ on the port.
[PE1-GigabitEthernet1/0/1] qinq enable
# Configure the port to tag VLAN 10 frames with outer VLAN ID 100.
[PE1-GigabitEthernet1/0/1] qinq vid 100
[PE1-GigabitEthernet1/0/1-vid-100] raw-vlan-id inbound 10
[PE1-GigabitEthernet1/0/1-vid-100] quit
# Configure the port to tag VLAN 20 frames with outer VLAN ID 200.
[PE1-GigabitEthernet1/0/1] qinq vid 200
[PE1-GigabitEthernet1/0/1-vid-200] raw-vlan-id inbound 20
[PE1-GigabitEthernet1/0/1-vid-200] quit
[PE1-GigabitEthernet1/0/1] quit
{ Configure GigabitEthernet 1/0/2:
# Configure GigabitEthernet 1/0/2 as a trunk port and assign it to VLAN 100 and VLAN 200.
[PE1] interface gigabitethernet 1/0/2
[PE1-GigabitEthernet1/0/2] port link-type trunk
[PE1-GigabitEthernet1/0/2] port trunk permit vlan 100 200
[PE1-GigabitEthernet1/0/2] quit
# Set the TPID in the outer VLAN tags to 0x8200.
[PE1] qinq ethernet-type 8200
2. Configure PE 2:
{ Configure GigabitEthernet 1/0/1:
# Configure GigabitEthernet 1/0/1 as a hybrid port to permit frames of VLAN 10 and VLAN
20 to pass through tagged, and frames of VLAN 100 and VLAN 200 to pass through
untagged.
[PE2] interface gigabitethernet 1/0/1
[PE2-GigabitEthernet1/0/1] port link-type hybrid
[PE2-GigabitEthernet1/0/1] port hybrid vlan 10 20 tagged
[PE2-GigabitEthernet1/0/1] port hybrid vlan 100 200 untagged
# Enable basic QinQ on the port.
[PE2-GigabitEthernet1/0/1] qinq enable
# Configure the port to tag VLAN 10 frames with outer VLAN ID 100.
[PE2-GigabitEthernet1/0/1] qinq vid 100
[PE2-GigabitEthernet1/0/1-vid-100] raw-vlan-id inbound 10
[PE2-GigabitEthernet1/0/1-vid-100] quit
# Configure the port to tag VLAN 20 frames with outer VLAN ID 200.
[PE2-GigabitEthernet1/0/1] qinq vid 200
[PE2-GigabitEthernet1/0/1-vid-200] raw-vlan-id inbound 20
[PE2-GigabitEthernet1/0/1-vid-200] quit
[PE2-GigabitEthernet1/0/1] quit
{ Configure GigabitEthernet 1/0/2:
# Configure GigabitEthernet 1/0/2 as a trunk port and assign it to VLAN 100 and VLAN 200.
[PE2] interface gigabitethernet 1/0/2
[PE2-GigabitEthernet1/0/2] port link-type trunk