Hydac FCU 1310 - Page 35

To Next Page

To Previous Page

Using the BatteryPack (accessory)

Pull the BatteryPack up and out of

the mounting rails.

Then insert the connector back into

the socket on the BatteryPack.

FCU1310

en(us)

Page 35 / 124

BeWa FCU1310 V300 3371346f en-us 2017-01-27.docx 2017-01-27

Main Page

Imprint2
Documentation Representative2
- Table of Contents3
Content3
What's New - Changes to the Manual7
Preface8
- Technical Support8
- Modifications to the Product8
- Warranty8
- Using the Documentation9
Safety Information10
- Hazard Symbols10
- Signal Words and Their Meaning in the Safety Information and Instructions11
- Structure of the Safety Information and Instructions12
- Observe Regulatory Information12
- Proper/Designated Use13
  - Periodic Intermittent Duty - Operating Mode S3, (as Per DIN en 60034-1 / DIN VDE 0530, Part 1)14
- Improper Use or Use Deviating from Intended Use15
- Qualifications of Personnel / Target Group16
- Wear Personal Protection Equipment17
- Stoppage in an Emergency (EMERGENCY STOP)17
Fcuopening/Closing18
Fcutransporting19
Fcustoring20
Decoding the Model Code Label21
Checking the Scope of Delivery23
What Can the Product Do24
- Counting Contaminant Particles25
- How the Product Works27
- Overview of Control Panel/Operating Elements28
- Dimensions29
- Hydraulic Diagram30
Using the Batterypack (Accessory)31
Preparing the FCU for Measurement36
- Connecting/Disconnecting the FCU Electrically36
- Plug In/Detach Return Hose37
- Selecting the Measurement Location38
- Select the Measurement Method According to the Pressure Involved39
- Measuring up to Max. 45 Bar / 650 Psi40
- Measuring in the Range 5 to 345 Bar / 217 to 5000 Psi43
- Measuring from Unpressurized Containers47
Fcuoperating49
- Display and Keypad Elements49
- Clicking through the Display51
  - Display51
  - Display52
- Displaying Measured Variables53
  - Measured Variable53
- Display Service Variables54
  - Service Variable54
Select Operating Level / Configuration Menu55
- Operate / Set up Menu56
- Operating/Setting Measuring Menu61
Performing Measurements67
Reading Internal Measurement Memory68
- Read out Measured Values Via DATA Interface69
- Reading out USB Interface Measured Values71
  - Copying Measurements Onto a USB Data Stick71
    - Data Transmission Failed74
- Reading out Measured Values Via Bluetooth Interface75
  - Installing the Bluetooth USB Adaptor76
    - Guarantee and Liability for the USB Adapter76
  - Connecting/Linking the FCU Via Bluetooth76
Evaluating Measurement Records77
- Measurement Record Directories According to Measurement Point77
- Measurement Report File Names77
- Opening Measurement Reports78
  - The Measurements Are Shown as Dates80
Evaluating/Reading Measurement Reports with Flumos82
Preparing the FCU for Transport83
Performing Maintenance87
- Fcucleaning87
- FCU Flushing88
- Clean the Suction Strainer92
- Checking the High Pressure Adapter96
  - Cleaning / Changing the Strainer in the High Pressure Adapter97
  - Cleaning / Changing the Strainer in the High Pressure Adapter98
Identifying and Interpreting Status/Error Messages99
Restarting/Resetting103
Taking the FCU out of Operation103
- Shutting down the FCU103
- Fcudisposing103
Locating Spare Parts104
- Selecting Accessories105
Checking the Measuring Accuracy107
- Fcucalibrating107
Technical Data108
Appendix110
- Model Code110
- Finding Customer Service / Service Stations111
- Factory Default Settings112
- Overview / Definition of the Cleanliness Classes113
- EC Declaration of Conformity119
- Explanation of Terms and Abbreviations121
- Index122

Hydac FCU 1310 - Page 35

Table of Contents