INDEX "
Index-2 VT220/ANSI Terminal Emulation Programmer’s Reference Guide
Backspace (BS)
encoded sequence, 9-46
local editing key, 8-67
received code, 8-5
terminating key, 8-54
Backtab key, 8-68
Bar code length, 9-34
Bar code scanning
data string formats, A-3
enabling algorithms, A-2
Encoded Code 39, 9-45
extended command, 9-30
host computer, A-2
line edit mode, 8-54
local edit mode, 8-69
Batteries, 1-5
BEL (bell), 8-5
Bell (BEL), 8-5
Block mode. See Line edit mode
Break (top-row function key)
PEN*KEY 6400, 6-20
PEN*KEY 6500, 7-14
RT1100, 3-15
RT1700, 4-18
RT3210, 2-15
RT5900, 5-15
transmitted code, 8-60
BS (backspace)
encoded sequence, 9-46
local editing key, 8-67
received code, 8-5
terminating key, 8-54
C
C0 codes, 8-3, 8-4–8-6
C1 codes, 8-7–8-10
CAN (cancel), 8-6
Cancel (CAN), 8-6
Cancel character (CCH), 8-10
Carriage return (CR), 8-5
CCH (cancel character), 8-10
Center cursor mode
PEN*KEY 6400, 6-2
PEN*KEY 6500, 7-2
RT1100, 3-2
RT1700, 4-2
RT3210, 2-2
RT5900, 5-2
Character encoding, 8-2
Character mode, 8-48, 8-55
Character rendition and attrib-
utes, 8-26–8-27
Character set (DECNRCM),
8-22
Character set selection
hard character sets, 8-15–8-16
locking shifts, 8-17
soft character sets, 8-15
Character sets
down-line loadable, 8-11, 8-42
Greek, 8-13–8-14
hard, 8-15–8-16
locking shifts, 8-17
multinational
7-bit control codes, 8-3
8-bit control codes, 8-7–8-8
left half, 8-4
right half, 8-8
national replacement,
8-13–8-14
not supported, 8-11
redefinable, 8-11, 8-42
soft, 8-15
special graphics, 8-11–8-12
supplemental graphics,
8-7–8-8
Character sizes
RT1100, 3-1
RT1700, 4-1
RT3210, 2-1
PEN*KEY 6500, 7-1
RT5900, 5-1
Character types
C0 codes, 8-3
C1 codes, 8-7–8-8
GL codes, 8-3–8-4
GR codes, 8-7–8-8
Codabar, 9-37
Code 11, 9-38
Code 128, 9-39
Code 39 algorithms, 9-36
Code 93, 9-39
Column (DECCOLM), 8-20
Columns, 8-20, 8-49
Compose character (special
function key)
code generated, 8-56
PEN*KEY 6400, 6-15, 6-16
PEN*KEY 6500, 7-9
RT1100, 3-11
RT1700, 4-14
RT3210, 2-11
RT5900, 5-11
Computer Identics 2of5, 9-40
Concatenation, 9-54
Control (special function key)
code generated, 8-56
PEN*KEY 6400, 6-16, 6-22
PEN*KEY 6500, 7-10, 7-14
RT1100, 3-11, 3-15
RT1700, 4-14, 4-19
RT3210, 2-11
RT5900, 5-11, 5-15
terminating key, 8-54
Control Byte 1, 9-31
Control Byte 2, 9-32
Control Byte 3, 9-33
Control sequence introducer
(CSI), 8-10
Corner mode
PEN*KEY 6400, 6-2
PEN*KEY 6500, 7-2
RT1100, 3-2
RT1700, 4-2
RT3210, 2-3
RT5900, 5-2
CR (carriage return), 8-5
CSI ? 1 h (Cursor key, applica-
tion), 8-20
CSI ? 2 l (VT52), 8-20
CSI ? 3 h (132 column), 8-20
CSI ? 3 l (80 column), 8-20
CSI ? l l (Cursor key, cursor),
8-20
CSI (control sequence
introducer), 8-10
CSI 1 2 h (Send/receive, off),
8-19
CSI 1 2 l (Send/receive, on), 8-19
CSI 2 0 h (New line), 8-20
CSI 2 0 l (Line feed), 8-20
CSI 2 h (Keyboard action,
locked), 8-19
To Next Page
Loading...