Contents
10 Lenze · i700 servo inverter · reference manual · DMS 3.0 EN · 06/2016 · TD06
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
9.4 CiA402 error codes / error messages _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 286
Error code 0x0000: No error
Error code 0x2320: Short circuit or earth leakage on motor side
Error code 0x2340: Short circuit on motor side
Error code 0x2351: Motor utilisation (I²xt) > [value] %
Error code 0x2380: Fault - utilisation of the power section (Ixt) too high
Error code 0x2381: Warning - Utilisation of the power section (Ixt) too high
Error code 0x2382: Fault - device utilisation (Ixt) too high
Error code 0x2383: Warning - device utilisation (Ixt) too high
Error code 0x2384: Ultimate motor current reached
Error code 0x2385: Output current > [value] A (maximum device current)
Error code 0x2386: Clamp is active
Error code 0x2387: Clamp responded too often
Error code 0x3210: DC link circuit - overvoltage [value] V
Error code 0x3220: DC link circuit - undervoltage [value] V
Error code 0x4210: Module temperature too high, [value]
Error code 0x4280: Internal fault - module temperature monitoring
Error code 0x4310: Motor temperature too high, [value]
Error code 0x4380: Motor temperature sensor
Error code 0x5112: 24-V supply
Error code 0x6010: Watchdog reset
Error code 0x6310: Incorrect parameter set download
Error code 0x6320: Parameter error in object [value]
Error code 0x7121: PLI - motor blocked
Error code 0x7303: Error in feedback system
Error code 0x7380: Hiperface communication error
Error code 0x7381: Hiperface: Invalid absolute value - motor speed too high
Error code 0x8180: ECAT DC - synchronisation required
Error code 0x8181: EtherCAT communication
Error code 0x8280: Sync Manager - address [value]
Error code 0x8281: Sync Manager - actual size [value]
Error code 0x8282: Sync Manager - settings [value]
Error code 0x8283: PDO Mapping: Object unknown (index [value])
Error code 0x8284: No PDO mapping object (index [value])
Error code 0x8285: Too many mapped objects (max. number = [value])
Error code 0x8286: PDO mapping - error
Error code 0x8700: Sync controller
Error code 0x8701: Time-out during synchronisation with EtherCAT Sync signal
Error code 0xFF00: Fatal internal error
Error code 0xFF01: Fatal internal communication error, cycle [value]
Error code 0xFF02: Brake
Error code 0xFF03: Fatal internal error - overflow task [value]
Error code 0xFF04: PLI - motor movement too large
Error code 0xFF05: STO inhibited
Error code 0xFF06: Max. speed reached
Error code 0xFF07: Impermissible during identification or in the test mode
Error code 0xFF08: Impossible during identification
Error code 0xFF09: Motor phase failure
Error code 0xFF0A: Motor phase failure - phase U
Error code 0xFF0B: Motor phase failure - phase V
Error code 0xFF0C: Motor phase failure - phase W
Error code 0xFF0D: No resolver connected --> command cannot be executed.
Error code 0xFF0E: Speed too low --> command cannot be executed.
Error code 0xFF0F: No resolver connected --> command cannot be executed.
Error code 0xFF10: Time-out
Error code 0xFF11: Numerical problem
To Next Page
Loading...
