BA053101-en
Pos: 3 91 /Te chnis che Dok umen tation/ Pap ierk orb/ Übers chri ften/ Übersc hrif t 1: I nsta ndha ltun g @ 11\mod_1231318736629_75.docx @ 289550 @ 1 @ 1
Pos: 392 /Tech nische D okumen tation/A lle G eräte/ Überschr iften/Üb ers chrifte n 1.1/W/ Übersc hrift 1.1: Wi chtige H inweis e @ 6\m od_1182863869546_75.docx @ 97710 @ 2 @ 1
Pos: 393 /Te chnis che Dok umenta tion/Leis tungsm esstech nik/- Ar chiv -/00 LPS Alle/Inhalte/Warnung!/Inhalt: Warnung - Ver letzu ng durch Str omschla g @ 1 4\mod_1241689165017_75.docx @ 372513 @ @ 1
Danger! Electric shock hazard!
• Only skilled electricians may work on electrical parts of the system!
• Before doing any maintenance work on the system disconnect it from the mains power supply
and secure it against switch on!
• The maintenance work to be
and the appropriate intervals are specified in the
following chapter (this applies if no other changes have been contractually agreed upon). These
kinds of maintenance work may only be done by authorized and trained personnel. Skilled per-
sonnel are those who are authorized and trained by the operator, the manufacturer and the re-
spective service partner.
Any other maintenance, installation or repair work on the dynamometer during the warranty pe-
riod may only be done by MAHA service technicians, those service partners authorized by MA-
HA or after consultation and approval by MAHA. The manufacturer warranty becomes invalid at
non-compliance.
• Inform the operating personnel before doing maintenance work.
Pos: 3 94 /Te chnis che Dok umen tation/ Pap ierk orb/ Übers chri ften/ Übersc hrif t 1.1 : Jä hrlic he Üb erpr üfung @ 6\m od_1 17448 22457 18_ 75.docx @ 7681 7 @ 2 @ 1
Pos: 3 95 /Te chnis che Dok umen tation/ All e Ger äte/I nha lte/I nfo!/I nha lt: Inf o - Jä hrlich e Überpr üfung @ 14\mod_1242051457491_75.docx @ 373548 @ @ 1
• The maintenance interval prescribed by the manufacturer is
.
This maintenance interval refers to normal workshop usage. If the equipment is used more fre-
quently or under severe operating conditions (e.g. outdoors), the interval must be reduced ac-
cordingly.
• Maintenance work shall be done only by authorized and trained service technicians provided by
the manufacturer, licensed dealers or service partners.
• In case of non-compliance the manufacturer's warranty becomes void.
Pos: 396 /Tech nische D okumen tation/P apierk orb/ Überschri ften/Üb erschr ift 1.1: Ins tandha ltung durc h den Betre iber @ 6\mod _11 78543 54439 0_75.d ocx @ 91 370 @ 2 @ 1
Maintenance by the Operator
Pos: 397 /Tech nische D okumen tation/A lle G eräte/ Überschr iften/Üb ers chrifte n 1.1.1/ R/Übersc hrif t 1.1.1: Rollensa tz @ 13\mod_1236773654894_75.docx @ 354743 @ 3 @ 1
Pos: 398 /Te chnis che D okum ent ati on/ Leis tun gsm esst ech nik/ POWE R DYN O/0 531 01 M SR/ BA/I nha lt: 053 1 Ins t Ro lle nsa tz @ 1 4\mod_1241690688702_75.docx @ 372565 @ @ 1
The MSR roller set should be inspected and serviced once a year or every 200 operating hours.
The roller set inspection includes an inspection of all anchorings and their screws. The screwing of
the cover plate is to be checked before starting the dyno.
Pos: 399 /Te chnis che D okum ent ation/A lle G eräte/ Überschr iften/Üb ers chrifte n 1.1.1/ W/Übersc hrif t 1.1.1: Wirbels trombr emse @ 13\m od_12 34874 55532 5_7 5.docx @ 34204 9 @ 3 @ 1
Pos: 400 /Te chnis che D okum ent ati on/ Leis tun gsm esst ech nik/ POWE R DYN O/0 523 01 LPS 3 000 R10 0/B A/I nhalt: 052 3 Wirbelstromb remse @ 13\mod_1234874674885_75.docx @ 342127 @ @ 1
• Grease the eddy current brake every 400 hours of operation until grease escapes at the vent
pipe.
Use "SUPERTELMACO III" grease only, no mixed greases or different brands!
In case of non-compliance the bearings may be destroyed!
To Next Page
Loading...
Need help?
General
