Why is the battery capacity too low on Mindray Heart Rate Monitor?
If the battery capacity of your Mindray Heart Rate Monitor is too low, the following steps are recommended. Replace the battery. Also, check the cable for correct connection and any damage. If the issue continues, the power board may be defective and require replacement.
Why is secondary display not working on Mindray Heart Rate Monitor?
If the secondary display on your Mindray Heart Rate Monitor is not functioning, first check that the cable between the display and the patient monitor is correctly connected and undamaged. If the connection is secure, the DVI interface board may be defective and require replacement.
What to do if the touchscreen on Mindray DPM 6 is not responding?
If the touchscreen on your Mindray Heart Rate Monitor is unresponsive, check if there is a symbol shown above the [Main Menu] QuickKey. If present, press the [Main Menu] QuickKey for more than 3 seconds to enable the touchscreen.
How to improve print quality on Mindray DPM 6 Heart Rate Monitor?
If your Mindray Heart Rate Monitor is experiencing poor print quality or paper feed issues, first, stop the recorder and reinstall the paper roll correctly. Inspect the thermal print head and paper roller for any foreign matter, and clean the print head with a suitable cleaning solution. If the problem persists, the print head or the recorder itself may be failing and require replacement.
How to fix Mindray DPM 6 Heart Rate Monitor battery that won't recharge?
If the battery on your Mindray Heart Rate Monitor cannot be recharged, the following steps are recommended. First, replace the battery and attempt to recharge the new battery to determine if the original battery is faulty. Also, check the cable between the battery interface board and the power module for proper connection and any damage. If the issue persists, the power board may be defective and require replacement.
Why is the display blank on my Mindray Heart Rate Monitor?
If the integrated display on your Mindray Heart Rate Monitor is blank but the monitor functions correctly, check the cable from the display to the motherboard and the cables from the backlight board to the button board and the display for secure connections and any damage. If the connections are good, the backlight board, power module, or the display itself may be defective and require replacement.
Why there is no alarm sound on my Mindray DPM 6?
If your Mindray Heart Rate Monitor's alarm lamp is lit but there's no sound, first, check if the audio alarm is disabled in the settings menu under [Main Menu]?[Maintenance >>]? [User Maintenance >>]?enter the required password?[Alarm Setup >>], and then in the popup menu, set [Minimum Alarm VolumeAlm Sound] to appropriate setting.[On] In the [Others] window of the [Alarm Setup] menu, set [Alm Volume] to appropriate setting.. Also, inspect the cable between the speaker and the motherboard for proper connection and damage. If the issue persists, consider that there might be an FPGA audio logic error (requiring an upgrade), a speaker failure, or a motherboard failure, each necessitating component replacement or further action.
What to do if Mindray Heart Rate Monitor has no printout?
If your Mindray Heart Rate Monitor is not printing, check the following: 1. Verify the recorder module is enabled, checking the recorder status LED. 2. Ensure the paper roll is correctly installed. 3. Check the cable connection between the recorder and the motherboard for proper connection and damage. 4. Verify the power module outputs 5V DC and 12V DC correctly. If these steps don't resolve the issue, the recorder itself may need replacement.
Defines safety terms (DANGER, WARNING, CAUTION, NOTE) and equipment symbols.
Lists common problems, causes, guidance on parts, and how to check monitor status and software.
Solutions for power, display, module rack, and alarm system failures.
Covers inspection criteria for power cords, device enclosures, and labels.
Describes procedures for protective earth resistance and earth leakage current tests.
Details tests for patient leakage, mains on applied part leakage, and patient auxiliary current.
Provides a form for inspection and guidelines for safety checks after repair.
General| Display | TFT color LCD |
|---|---|
| Heart Rate Measurement | 30-300 bpm |
| ECG | 3/5-lead ECG |
| SpO2 | 0-100% |
| NIBP | Adult, pediatric, neonatal modes |
| Respiration | 0-120 bpm |
| Temperature | 0-50°C |
| Battery | Rechargeable lithium-ion |
| Networking | Ethernet, Wi-Fi optional |
| Connectivity | RS-232 |
| Power Supply | 100-240 VAC, 50/60 Hz |
| Measurement Parameters | ECG, SpO2, NIBP, respiration, temperature |
To Next Page
