Multilin SR469 - 4.12 S11 MONITORING

4. SETPOINT PROGRAMMING S11 MONITORING
4-63
4.11.7 OVER TORQUE SETUP
y
#29(572548(
y
#>(17(5@#IRU#PRUH
Õ
ÕÕ
Õ
ENTER
ENTERENTER
ENTER
ESCAPE
ESCAPEESCAPE
ESCAPE
Ö
ÖÖ
Ö 29(572548(
$/$50=##2II
B1>75*ð?VVäð<QdSXUTäðE^\QdSXUT
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
$66,*1#$/$50#5(/$<6=
$ODUP
B1>75*ð1\Qb]äð1\Qb]ðêð1ehY\YQbi"äð1\Qb]ðêð1eh"ðêð1eh#äðð1\Qb]ðêð1ehY\YQbið#ä
1ehY\YQbið"äð1eh"ðêð1eh#äð1ehY\YQbið#
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
29(5#72548(#$/$50
/(9(/=###############733313#1P
B1>75*ð!â ðd_ð))))))â)
CD5@*ð â!
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
29(5#72548(#$/$50
'(/$<=######413V
B1>75*ð â"ðd_ð#
CD5@*ð â!
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
29(5#72548(#$/$50
(9(176=###2II
B1>75*ðð?^äð?VV
FUNCTION:
If it is desired to detect an overtorque condition on a motor, usually done to protect devices driven by the motor, it can be set up here.
The assigned relay will activate when the torque measured exceeds the specified level for the specified time duration.
4.12.1 TRIP COUNTER
y
#75,3#&2817(5
y
#>(17(5@#IRU#PRUH
Õ
ÕÕ
Õ
ENTER
ENTERENTER
ENTER
ESCAPE
ESCAPEESCAPE
ESCAPE
Ö
ÖÖ
Ö 75,3#&2817(5
$/$50=#2II
B1>75* ?VVäð<QdSXUTäðE^\QdSXUT
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
$66,*1#$/$50#5(/$<6=
$ODUP
B1>75*ð1\Qb]äð1\Qb]ðêð1ehY\YQbi"äð1\Qb]ðêð1eh"ðêð1eh#äð1\Qb]ðêð1ehY\YQbi#äð1ehY\YQbi"äð
ðð1eh"ðêð1eh#äð1ehY\YQbi#
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
75,3#&2817(5
$/$50=#58#75,36
B1>75* !ðãð%
CD5@*ð!
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
×
××
×
75,3#&2817(5#$/$50
(9(176=#2II
B1>75* ?^äð?VV
FUNCTION:
The Trip Counter alarm will function as follows: when the Trip Counter Limit is reached, an alarm will occur. The trip counter must be
cleared or the alarm level raised and the reset key must be pressed (if the alarm was latched) to reset the alarm.
EXAMPLE:
It might be useful to set a Trip Counter alarm at 100 such
that if 100 trips occur, the resulting alarm would prompt the
operator or supervisor to investigate the type of trips that
have occurred. A breakdown of trips by type may be found
on A3 MAINTENANCE, under TRIP COUNTERS. If a trend
is detected, it would warrant further investigation.
4.12
S11
MONITORING