5. ACTUAL VALUES A2 METERING DATA
5-11
5.3.5
POWER METERING
y
32:(5#0(7(5,1*
y
>(17(5@#IRU#PRUH
Õ
ÕÕ
Õ
ENTER
ENTERENTER
ENTER
ESCAPE
ESCAPEESCAPE
ESCAPE
Ö
ÖÖ
Ö 32:(5#)$&725=
3133
RANGE: 0.01-0.99 Lead or Lag, 0.00, 1.00
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
5($/#32:(5=
#######3#N:
RANGE: 0 - ±50000
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
5($/#32:(5=
#######3#KS
RANGE: 0 - ±67024
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
5($&7,9(#32:(5=
#######3#NYDU
RANGE: 0 - ±50000
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
$33$5(17#32:(5=
#######3#N9$
RANGE: 0 - 50000
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
326,7,9(#:$77+2856=
########31333#0:K
RANGE: 0.000 - 999999.999
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
326,7,9(#9$5+2856=
########31333#0YDUK
RANGE: 0.000 - 999999.999
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
×
××
×
1(*$7,9(#9$5+2856=
########31333#0YDUK
RANGE: 0.000 - 999999.999
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
×
××
×
72548(=
########33313#1P
RANGE: 0.0 - 999999.9
NOTE: This message is seen only if the TORQUE METERING is enabled.
DESCRIPTION:
The values for power metering and 3∅ total power quantities are displayed here. Watthours and varhours can also be seen here.
NOTE: An induction motor by convention consumes Watts and vars (+Watts and +vars). A synchronous motor can generate
vars (–vars) and feed them back to the power system.
If no VT Ratio is programmed in S2 SYSTEM SETUP, the following flash message will appear when an attempt is made to enter this
group of messages.
7+,6#)($785(##127
352*5$00('
5.3.6
TORQUE ALARM MESSAGE
72548(
#$/$50=###########33313
Alarm Status
Alarm StatusAlarm Status
Alarm Status
The above message will appear in the Alarm Status Event Record (if programmed) and as a display message when an overtorque alarm
occurs.
To Next Page
Loading...
