5. ACTUAL VALUES DIAGNOSTICS
5-25
5.8.2
FLASH MESSAGES
Flash messages are warning, error, or general information messages that are temporarily displayed in response to certain key presses.
These messages are intended to assist with navigation of the SR469 messages by explaining what has happened or by prompting the
user to perform certain actions.
.
Table 5-3 FLASH MESSAGES
1(:#6(732,17#+$6#
%((1#6725('
5281'('#6(732,17
+$6#%((1#6725(' -
287#2)#5$1*($#(17(5=
&&&&0&&&&&##E\##&
$&&(66#'(1,('/
6+257#$&&(66#6:,7&+
$&&(66#'(1,('/
(17(5#3$66&2'(
,19$/,'#3$66&2'(
(17(5('#$
1(:#3$66&2'(
+$6#%((1#$&&(37('
3$66&2'(#6(&85,7<
127#(1$%/('/#(17(5#3
3/($6(#(17(5#$
1210=(52#3$66&2'(
6(732,17#$&&(66#,6
12:#3(50,77('
6(732,17#$&&(66#,6
12:#5(675,&7('
'$7(#(175<#:$6
127#&203/(7(
'$7(#(175<
287#2)#5$1*(
7,0(#(175<#:$6
127#&203/(7(
7,0(#(175<
287#2)#5$1*(
12#75,36#25#$/$506
72#5(6(7
5(6(7#3(5)250('
68&&(66)8//<
$//#3266,%/(#5(6(76
+$9(#%((1#3(5)250('
&21',7,21#,6#35(6(17
5(6(7#127#3266,%/(
$5(#<28#685("#35(66
>(17(5@#72#9(5,)<
35(66#>(17(5@#72#$''
'()$8/7#0(66$*(
'()$8/7#0(66$*(
+$6#%((1#$''('
'()$8/7#0(66$*(
/,67#,6#)8//
35(66#>(17(5@#72
5(029(#0(66$*(
'()$8/7#0(66$*(
+$6#%((1#5(029('
'()$8/7#0(66$*(6
#9#RI#53#$5(#$66,*1('
,1387#)81&7,21
$/5($'<#$66,*1('
,19$/,'#6(59,&(
&2'(#(17(5('
.(<#35(66('#,6
,19$/,'#+(5(
'$7$#&/($5('
68&&(66)8//<
723#2)#3$*( (1'#2)#3$*( 723#2)#/,67 (1'#2)#/,67 02725#67$57,1*
ψψ
ψψψψ
ψψ
4
ψψ
ψψψψ
ψψ
5
ψψ
ψψψψ
ψψ
6
ψψ
ψψψψ
ψψ
7
ψψ
ψψψψ
ψψ
8
ψψ
ψψψψ
ψψ
9
ψψ
ψψψψ
ψψ
>1@#.(<#,6#86('#72
$'9$1&(#7+(#&85625
12#$/$506#$&7,9( 12#67$57#%/2&.6
$&7,9(
7+,6#)($785(##127
352*5$00('
-$SSURSULDWH#YDOXHV#ZLOO#EH
VXEVWLWXWHG#IRU#WKH#&#VLJQV
NEW SETPOINT HAS BEEN STORED:
This message appear each time a setpoint has been altered and stored as shown on the dis-
play.
ROUNDED SETPOINT HAS BEEN STORED:
Since the SR469 has a numeric keypad, a setpoint value may entered that is in between
valid setpoint values. The SR469 will detect this condition and store a value that has been rounded to the nearest valid setpoint value.
To find the valid range and step for a given setpoint, simply press the [HELP] key while the setpoint is being displayed.
OUT OF RANGE! ENTER: #### - ##### by #:
If a setpoint value that is outside of the acceptable range of values is entered, the SR469
will display this message, substituting the proper values for that setpoint. An appropriate value may then be entered.
ACCESS DENIED, SHORT ACCESS SWITCH:
In order to store any setpoint values, the Access Switch must be shorted. If this mes-
sage appears and it is necessary to change a setpoint, short the Access terminals C1 & C2.
ACCESS DENIED, ENTER PASSCODE:
The SR469 has a PASSCODE SECURITY feature. If that feature has been enabled, not only
do the Access Switch terminals have to be shorted, but the Passcode must also be entered. If the correct passcode has been lost or
forgotten, contact the factory with the Encrypted access code. All passcode features may be found in S1 SR469 SETUP under
PASSCODE.
INVALID PASSCODE ENTERED:
If an invalid passcode is entered for passcode security feature, this message will flash on the display.
NEW PASSCODE HAS BEEN ACCEPTED:
When changing the Passcode for the Passcode Security feature, this message will appear
as an acknowledge that the new passcode has been accepted.
PASSCODE SECURITY NOT ENABLED, ENTER 0:
The Passcode Security feature is disabled whenever the passcode is zero (factory
default). Any attempts to enter a passcode when the feature is disabled will result in this flash message. It is meant to prompt the user to
enter 0 as the passcode. When this has been done, the feature may be enabled by entering a non-zero passcode.
PLEASE ENTER A NON-ZERO PASSCODE:
If the passcode is zero, the passcode security feature is disabled. If the Change Pass-
code Setpoint is entered as yes, this flash message will appear prompting the user to enter a non-zero passcode which in turn will en-
able the feature.
SETPOINT ACCESS IS NOW PERMITTED:
Any time that the Passcode Security feature is enabled and a valid passcode is entered,
this flash message will appear to notify that the Setpoint s may now be altered and stored.
To Next Page
Loading...
