Multilin SR469 - Analog in Min;Max

5. ACTUAL VALUES A3 LEARNED DATA
5-17
5.4.4 ANALOG IN MIN/MAX
y
$1$/2*#,13876
y
>(17(5@#IRU#PRUH
Õ
ÕÕ
Õ
ENTER
ENTERENTER
ENTER
ESCAPE
ESCAPEESCAPE
ESCAPE
Ö
ÖÖ
Ö $QDORJ#,23#4
0,1=3#8QLWV
RANGE: -50000 to +50000 * Message not seen if analog input programmed as “None”
*The message will reflect the Analog Input name and units as programmed,
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
$QDORJ#,23#4
0$;=3#8QLWV
RANGE: -50000 to +50000 * Message not seen if analog input programmed as “None”
*The message will reflect the Analog Input name and units as programmed,
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
$QDORJ#,23#5
0,1=3#8QLWV
RANGE: -50000 to +50000 * Message not seen if analog input programmed as “None”
*The message will reflect the Analog Input name and units as programmed,
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
$QDORJ#,23#5
0$;=3#8QLWV
RANGE: -50000 to +50000 * Message not seen if analog input programmed as “None”
*The message will reflect the Analog Input name and units as programmed,
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
$QDORJ#,23#6
0,1=3#8QLWV
RANGE: -50000 to +50000 * Message not seen if analog input programmed as “None”
*The message will reflect the Analog Input name and units as programmed,
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
$QDORJ#,23#6
0$;=3#8QLWV
RANGE: -50000 to +50000 * Message not seen if analog input programmed as “None”
*The message will reflect the Analog Input name and units as programmed,
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
$QDORJ#,23#7
0,1=3#8QLWV
RANGE: -50000 to +50000 * Message not seen if analog input programmed as “None”
*The message will reflect the Analog Input name and units as programmed,
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
×
××
×
$QDORJ#,23#7
0$;=3#8QLWV
RANGE: -50000 to +50000 * Message not seen if analog input programmed as “None”
*The message will reflect the Analog Input name and units as programmed,
DESCRIPTION:
The SR469 will learn the Minimum and Maximum values of the analog inputs since they were last cleared. This information can be
cleared using the setpoint in S1 SR469 SETUP under CLEAR DATA. When the data is cleared, the present value of each analog input will
be loaded as a starting point for both minimum and maximum. The name of the input and the units will reflect those programmed for each
input.
If no Analog Inputs are programmed in S12 ANALOG I/O, the following flash message will appear when an attempt is made to enter this
group of messages.
7+,6#)($785(##127
352*5$00('