Multilin SR469 - Start Blocks

A1 STATUS 5. ACTUAL VALUES
5-6
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
NYDU#'(0$1'
$/$50=#0#5333#NYDU
RANGE: -50000 to +50000
Note: The current value of Running kW Demand will be shown here
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
N9$#'(0$1'
$/$50=#5395#N9$
RANGE: 0 to +50000
Note: The current value of Running kVA Demand will be shown here
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
$QDORJ#,23#4
$/$50=#534#8QLWV
RANGE: -50000 to +50000 *The alarm message will reflect the Analog Input name and units as programmed,
Note: The level of the analog input will be shown here
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
(0(5*(1&<#5(67$57=
7ULS#6WLOO#3UHVHQW
RANGE: Trip Still Present, Block Still Present, No Trips & No Blocks
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
×
××
×
$/$50/#6579<#127
,16(57('#3523(5/<
Note: If the SR469 chassis is only partially engaged with the SR469 case, this Service alarm will appear
after 1 second. Secure the chassis handle to ensure that all contacts mate properly.
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
×
××
×
6579<#127#,1#6(59,&(
6LPXODWLRQ#0RGH
Range: Not Programmed, Simulation Mode, Output Relays Forced, Analog Output Forced, Test Switch
Shorted.
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
×
××
×
57'#&4
+,#$/$50=############468ƒ&
RANGE: 1 - 250
Note: Similar Hi Alarms will occur for the other RTDs. The alarm message will reflect the alarm name as
programmed.
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
×
××
×
$QDORJ#405
$/$50=###################83(
RANGE: 0 - 999 (% Diff) or 0 - 99999 (Abs Diff)
* The alarm message will reflect the Analog Input name and units as programmed.
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
×
××
×
$QDORJ#607
$/$50=###################83(
RANGE: 0 - 999 (% Diff) or 0 - 99999 (Abs Diff)
* The alarm message will reflect the Analog Input name and units as programmed.
DESCRIPTION:
Any active alarms may be viewed here.
5.2.4 START BLOCKS
y
#67$57#%/2&.6
y
#>(17(5@#IRU#PRUH
Õ
ÕÕ
Õ
ENTER
ENTERENTER
ENTER
ESCAPE
ESCAPEESCAPE
ESCAPE
Ö
ÖÖ
Ö 12#67$57#%/2&.6
$&7,9(
RANGE: N/A
Note: This message seen when no start blocks are active
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
29(5/2$'#/2&.287
%/2&.=#58#PLQ
RANGE: 0 - 500
NOTE: this message is seen only after an overload trip
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
67$57#,1+,%,7#%/2&.
/2&.287#7,0(=#53#PLQ
RANGE: 1 - 2500
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
67$5762+285#%/2&.
/2&.287#7,0(=#53#PLQ
RANGE: 1 - 60
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
7,0(#%(7:((1#67$576
/2&.287#7,0(=#53#PLQ
RANGE: 1 - 500
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
5(67$57#%/2&.
/2&.287=##6#PLQ#7<#V
RANGE: 1s to 833 min
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
×
××
×
%/2&.#67$57
6579<#127#352*5$00('
RANGE: N/A
NOTE: This message seen if the Phase CT Primary and Motor FLA not programmed
DESCRIPTION:
Any active blocking functions may be viewed here.