Multilin SR469 - General Counters; Timers

5. ACTUAL VALUES A4 MAINTENANCE
5-19
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
$QDORJ#,23#4
75,36=#3
RANGE: 0 -50000
*The message will reflect the Analog Input name and units as programmed,
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
$QDORJ#,23#5
75,36=#3
RANGE: 0 -50000
*The message will reflect the Analog Input name and units as programmed,
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
$QDORJ#,23#6
75,36=#3
RANGE: 0 -50000
*The message will reflect the Analog Input name and units as programmed,
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
$QDORJ#,23#7
75,36=#3
RANGE: 0 - 50000
*The message will reflect the Analog Input name and units as programmed,
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
×
××
×
$QDORJ#405
75,36=#3
RANGE: 0 - 50000
*The message will reflect the Analog Input name and units as programmed,
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
×
××
×
$QDORJ#607
75,36=#3
RANGE: 0 - 50000
*The message will reflect the Analog Input name and units as programmed,
DESCRIPTION:
A breakdown of number of trips by type is displayed here. When the Total reaches 50000, all counters reset. This infor-
mation can be cleared using the setpoint in S1 SR469 SETUP under CLEAR DATA.
5.5.2 GENERAL COUNTERS
y
*(1(5$/#&2817(56
y
>(17(5@#IRU#PRUH
Õ
ÕÕ
Õ
ENTER
ENTERENTER
ENTER
ESCAPE
ESCAPEESCAPE
ESCAPE
Ö
ÖÖ
Ö 180%(5#2)#02725
67$576=#3
RANGE: 0 - 50000
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
180%(5#2)#(0(5*(1&<
5(67$576=#3
RANGE: 0 -50000
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
180%(5#2)#67$57(5
23(5$7,216=#3
RANGE: 0 -50000
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
×
××
×
',*,7$/#&2817(5=
#####################3##8QLWV
RANGE: 0 - 1 000 000 000
*Seen only if one of the Assignable Digital Inputs is programmed as Digital Counter
DESCRIPTION:
Two of the SR469 General counters will count the number of motor starts or start attempts and the number of Emergency Restarts per-
formed to start a given motor over time. This may be useful information when troubleshooting a motor failure. When either of these
counters reaches 50000, that counter will reset to 0. This information can be cleared using the setpoint in S1 SR469 SETUP under
INSTALLATION, RESET MOTOR INFORMATION. Another of the SR469 General counters will count the number of starter operations
performed over time. This counter is incremented any time the motor is stopped, either by a trip or normal stop. This may be useful
information for starter maintenance. When the counter reaches 50000, that counter will reset to 0. This information can be cleared using
the setpoint in S1 SR469 SETUP under INSTALLATION, RESET STARTER INFORMATION. If one of the Assignable Digital Inputs is pro-
grammed as Digital Counter, that counter measurement will appear here. The counter can be reset to zero if the counter is of the increment-
ing type or pre-set to a predetermined value using the setpoint in S1 SR469 SETUP under CLEAR DATA.
5.5.3 TIMERS
y
7,0(56
y
>(17(5@#IRU#PRUH
Õ
ÕÕ
Õ
ENTER
ENTERENTER
ENTER
ESCAPE
ESCAPEESCAPE
ESCAPE
Ö
ÖÖ
Ö 02725#5811,1*
+2856=#3#KU
RANGE: 0 - 100000
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
7,0(#%(7:((1#67$576
7,0(5=#3#PLQ
RANGE: 0 - 500
Û
ÛÛ
Û
ESCAPE
ESCAPEESCAPE
ESCAPE
MESSAGE
MESSAGEMESSAGE
MESSAGE
Ú
ÚÚ
Ú
67$5762+285#7,0(56
##3####3####3####3####3##PLQ
RANGE: 0 - 60
DESCRIPTION:
One of the SR469 timers accumulates the total running time for the Motor. This may be useful for scheduling routine maintenance.
When this timer reaches 100 000, it will reset to 0. This timer can be cleared using the setpoints in S1 SR469 SETUP under
INSTALLATION, RESET MOTOR INFORMATION.