Multilin SR469 - Page 4

SR469 MANUAL
TABLE OF CONTENTS
iii
4.12.2 STARTER FAILURE...................................................................................................................................................................................4-63
4.12.3 CURRENT, k
W
, kvar, kVA DEMAND .........................................................................................................................................................4-64
4.12.4 PULSE OUTPUT........................................................................................................................................................................................4-66
4.13 S12 ANALOG I/O.............................................................................................................................................................. 4-67
4.13.1 ANALOG OUTPUTS 1-4 ............................................................................................................................................................................4-67
4.13.2 ANALOG INPUTS 1-4 ................................................................................................................................................................................4-69
4.13.3 ANALOG IN DIFF 1-2.................................................................................................................................................................................4-70
4.13.4 ANALOG IN DIFF 3-4.................................................................................................................................................................................4-71
4.14 S13 SR469 TESTING ....................................................................................................................................................... 4-72
4.14.1 SIMULATION MODE..................................................................................................................................................................................4-72
4.14.2 PRE-FAULT SETUP...................................................................................................................................................................................4-73
4.14.3 FAULT SETUP ...........................................................................................................................................................................................4-74
4.14.4 TEST OUTPUT RELAYS ...........................................................................................................................................................................4-75
4.14.5 TEST ANALOG OUTPUT...........................................................................................................................................................................4-75
4.14.6 COMM PORT MONITOR ...........................................................................................................................................................................4-76
4.14.7 MULTILIN USE ONLY................................................................................................................................................................................4-76
4.15 S14 TWO-SPEED MOTOR............................................................................................................................................... 4-77
4.15.1 SPEED2 O/L SETUP ................................................................................................................................................................................4-77
4.15.2 SPEED2 UNDERCURRENT......................................................................................................................................................................4-79
4.15.3 SPEED2 ACCELERATION ........................................................................................................................................................................4-79
5. ACTUAL VALUES ....................................................................................................................5-1
5.1 OVERVIEW ..........................................................................................................................................................................5-1
5.1.1 ACTUAL VALUES MESSAGES.....................................................................................................................................................................5-1
5.2 A1 STATUS .......................................................................................................................................................................... 5-2
5.2.1 MOTOR STATUS...........................................................................................................................................................................................5-2
5.2.2 LAST TRIP DATA...........................................................................................................................................................................................5-3
5.2.3 ALARM STATUS............................................................................................................................................................................................5-5
5.2.4 START BLOCKS............................................................................................................................................................................................5-6
5.2.5 DIGITAL INPUTS ...........................................................................................................................................................................................5-7
5.2.6 REAL TIME CLOCK .......................................................................................................................................................................................5-7
5.3 A2 METERING DATA...........................................................................................................................................................5-8
5.3.1 CURRENT METERING..................................................................................................................................................................................5-8
5.3.2 TEMPERATURE ............................................................................................................................................................................................5-9
5.3.3 VOLTAGE METERING.................................................................................................................................................................................5-10
5.3.4 SPEED .........................................................................................................................................................................................................5-10
5.3.5 POWER METERING....................................................................................................................................................................................5-11
5.3.6 TORQUE ALARM MESSAGE......................................................................................................................................................................5-11
5.3.7 DEMAND METERING..................................................................................................................................................................................5-12
5.3.8 ANALOG INPUTS ........................................................................................................................................................................................5-12
5.3.9 PHASORS....................................................................................................................................................................................................5-13
5.4 A3 LEARNED DATA ........................................................................................................................................................... 5-15
5.4.1 MOTOR STARTING.....................................................................................................................................................................................5-15
5.4.2 AVERAGE MOTOR LOAD...........................................................................................................................................................................5-15
5.4.3 RTD MAXIMUMS .........................................................................................................................................................................................5-16
5.4.4 ANALOG IN MIN/MAX..................................................................................................................................................................................5-17
5.5 A4 MAINTENANCE ............................................................................................................................................................5-18
5.5.1 TRIP COUNTERS........................................................................................................................................................................................5-18
5.5.2 GENERAL COUNTERS...............................................................................................................................................................................5-19
5.5.3 TIMERS........................................................................................................................................................................................................5-19
5.6 A5 EVENT RECORDER ....................................................................................................................................................5-20
5.6.1 EVENT01 -EVENT40 ...................................................................................................................................................................................5-20
5.7 A6 PRODUCT INFO .......................................................................................................................................................... 5-22
5.7.1 SR469 MODEL INFO ...................................................................................................................................................................................5-22
5.7.2 CALIBRATION INFO....................................................................................................................................................................................5-22
5.8 DIAGNOSTICS ................................................................................................................................................................... 5-23
5.8.1 DIAGNOSTIC MESSAGES FOR OPERATORS .........................................................................................................................................5-23
5.8.2 FLASH MESSAGES.....................................................................................................................................................................................5-24
6. COMMUNICATIONS.................................................................................................................6-1
6.1 ELECTRICAL INTERFACE...................................................................................................................................................6-1
6.1.1 ELECTRICAL INTERFACE............................................................................................................................................................................6-1