EasyManuals Logo

NETGEAR GS748T User Manual

NETGEAR GS748T
302 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #220 background imageLoading...
Page #220 background image
220
GS748T Smart Switch
Source Prefix/Prefix Length: Specify IPv6 Prefix combined with IPv6 Prefix length of
the network or host from which the packet is being sent. Prefix length can be in the
range (0 to 128).
Source L4 Port: Specify a packet's source layer 4 port as a match condition for the
selected IPv6 ACL rule. Source port information is optional. Source port information
can be specified in two ways:
Select keyword “other” from the drop-down menu and specify the number of the
port in the range from 0 to 65535.
Select one of the keyword from the list: DOMAIN, ECHO, FTP, FTPDATA, HTTP,
SMTP, SNMP, TELNET, TFTP, and WWW. Each of these values translates into its
equivalent port number, which is used as both the start and end of the port range.
Destination Prefix/Prefix Length: Enter up to 128-bit prefix combined with prefix
length to be compared to a packet's destination IP Address as a match criteria for the
selected IPv6 ACL rule. Prefix length can be in the range (0 to 128).
Destination L4 Port: Specify a packet's destination layer 4 port as a match condition
for the selected IPv6 ACL rule. Destination port information is optional. Destination
port information can be specified in two ways:
Select keyword “other” from the drop-down menu and specify the number of the
port in the range from 0 to 65535.
Select one of the keyword from the list: DOMAIN, ECHO, FTP, FTPDATA, HTTP,
SMTP, SNMP, TELNET, TFTP, and WWW. Each of these values translates into its
equivalent port number, which is used as both the start and end of the port range.
Flow Label: Flow label is 20-bit number that is unique to an IPv6 packet, used by end
stations to signify quality-of-service handling in routers. Flow label can be specified
within the range (0 to 1048575).
IPv6 DSCP Service: Specify the IP DiffServ Code Point (DSCP) field. The DSCP is
defined as the high-order six bits of the Service Type octet in the IPv6 header. This is
an optional configuration. Enter an integer from 0 to 63. The IPv6 DSCP is selected
by possibly selection one of the DSCP keyword from a drop-down menu. If a value is
to be selected by specifying its numeric value, then select the Other option in the
drop-down menu and a text box will appear where the numeric value of the DSCP can
be entered.
3. Click Cancel to cancel the configuration on the screen and reset the data on the screen to
the latest value of the switch.
4. To add the new rule to the ACL, click Apply.
5. To delete a rule from an ACL, select the check box associated with the rule and click Delete.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NETGEAR GS748T and is the answer not in the manual?

NETGEAR GS748T Specifications

General IconGeneral
Basic switching RJ-45 Ethernet ports quantity48
MAC address table16000 entries
Packet buffer memory1.632 MB
Maximum data transfer rate1 Gbit/s
Latency20 µs
I/O ports48 RJ-45 connectors for 10BASE-T, 100BASE-TX, and 1000BASE-T (Auto Uplink on all ports) 4 SFP slots for fiber Gigabit Ethernet modules
Dimensions (WxDxH)440 x 260 x 43 mm
Power requirements100-240VAC 50/60 Hz
Networking features10BASE-T, 100BASE-TX, 1000BASE-T
Connectivity technologyWired
Full duplexYes
Networking standardsIEEE 802.3x
Minimum system requirementsCategory 5 network cables Network card for each PC Network software (e.g., Windows)
Mean time between failures (MTBF)69930 h
SafetyUL listed (UL 1950)/cUL, IEC950/EN60950
LED indicatorsLink, Power
Power consumption (typical)70 W
Storage temperature (T-T)-10 - 70 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 90 %
Weight and Dimensions IconWeight and Dimensions
Weight4000 g

Related product manuals