NXP Semiconductors MPC5746R User Manual

Table 61. Revision history
Revision Date Description of changes
• Removed IDDOFF.
• Added IDD_BD_STBY.
• Added IVDDA.
In section Input pad specifications :
• In Table 7 :
• Added footnote that supported input levels vary according to pad types.
• Corrected VILTTL Min and Max values.
• Corrected VIHAUTO, VILCMOS_H and VILCMOS Min value.
• In Table 8 :
• Modified |IWPU| Min values for condition Vin = VIH = 0.65 * VDD_HV_IO.
• Modified |IWPD| Min values for condition Vin = VIL = 0.35 * VDD_HV_IO.
• Removed the "Analog Input Leakeage and Pull-Up/Down DC electrical characteristics" table
and the preceding introductory paragraph to be moved to the ADC input description section.
In section Output pad specifications, Table 9, changed VOH and VOL specs to two separate specs
for 3V pads and 5V pads respectively. Corrected VOH Min and VOL Max values.
In section I/O pad current specifications :
• Added I/O Current Consumption tables.
• Modified NOTE on Excel file attached to the Reference Manual.
Added section Reset pad (PORST, RESET) electrical characteristics.
In section Oscillator and FMPLL :
• In Table 13, removed PLL0_PHI0 single period jitter row.
• In Table 15 :
• Modified footnote for CS_EXTAL and CS_XTAL.
• Modified gm (Oscillator Transconductance) spec.
• Removed VHYS.
In section ADC modules, revised the subsection structure and titles:
• Added section ADC input description with content moved from the "Input pad specifications"
section.
• Section "Input impedance and ADC accuracy" renamed to Input equivalent circuit and ADC
conversion characteristics with all content except Figure 11 and Table 19 removed.
• Removed erroneous section "SAR ADC electrical specification".
In section SAR ADC, Table 19 :
• Added footnote ("SAR ADC performance is not guaranteed...") to f
CK
symbol.
• Changed t
sample
specification min value to 250 ns (was 275).
• Added footnote to OFS and GNE. Changed OFS and GNE min and max values.
• Removed "Input (singe ADC channel)".
• Removed injection row for "Input (double ADC channel)".
• SNR, THD, SINAD, and ENOB specifications: changed frequency condition to 50 kHz (was
125 kHz).
• Changed SNR Min values.
• Added footnote to ENOB.
• Added I
DD_VDDA
, I
DD_VDDR
, and V
BG_REF
parameters.
In section S/D ADC, Table 20 :
• For V
IN_PK2PK
parameter second and third rows, changed V
SS
in Conditions to V
DD
.
• For f
ADCD_M
specification, removed sampling frequency footnote from parameter.
• Added footnote to RESOLUTION value.
• For |δ
GAIN
| specification added footnote to parameter and added new row with more detailed
"After calibration" conditions.
• Moved footnote "S/D ADC is functional in the range..." from the Z
IN
to the SNR parameters.
Table continues on the next page...
Revision history
SPC5746R Microcontroller Data Sheet, Rev. 6, 06/2017
92 NXP Semiconductors

NXP Semiconductors MPC5746R Specifications

General

Architecture	Power Architecture
Core	e200z4
Max CPU Frequency	160 MHz
Flash Memory	4 MB
RAM	512 KB
Operating Voltage	3.3 V
Operating Temperature	-40°C ~ 125°C
ADC	12-bit
Timers	GPT, STM
Communication Interfaces	CAN, LIN, SPI, Ethernet
Oscillator Type	External oscillator
Package	144-LQFP