Panasonic CZ-CFUNC2

ー 68 ー
Operating Instructions Intelligent Controller
44
Setting a schedule
Operation/Status
6
Register setting cells.
z Repeat the following (1) to (3) to register setting cells.
(1) Touch [New data].
z The “Sttg” dialogue is displayed. z In the “Sttg” dialogue, set “Time”, “ON/OFF”,
“OpertnMode”, “Temperatre”, “Fan SPD”, “Flap”, “Prhbt”, and “EnerSavStg”.
6-
1
(2) Change the settings.
Item Explanation
Time Set the time for the operation.
1) Touch [Time]. 2)
Use
to set the “hour” and
“minute”.
ON/OFF Set whether to start or stop operation.
1) Touch [ON/OFF]. 2) Select “ON” or “OFF”.
OpertnMode Set the operating mode.
1) Touch [OpertnMode]. 2)
Select the operating mode (
(heating),
(drying), (cooling), (fan),
(automatic)).
Item Explanation
Temperatre Set the temperature.
1) Touch [Temperatre]. 2)
Set the temperature with
and .
(± in 1 °C steps) Setting ranges
y In cooling or drying mode: Between 18 °C
and 30 °C
y In heating mode: Between 16 °C and
30 °C*
1
y Automatic: Between 17 °C and 27 °C
*1 The upper limit for gas heat pump air
conditioners is 26 °C.
Fan SPD Set the strength of the fan.
1) Touch [Fan SPD]. 2)
Select the fan speed (
(high), (mid),
(low), (automatic)).
Flap Set the direction of the airow.
1) Touch [Flap]. 2)
Set the ap to the desired position (
(F1),
(F2), (F3), (F4), (F5),
(Swing)).
y Heating, fan, and automatic (heating) can
be adjusted in 5 steps and cooling and dry can be adjusted in 3 steps.
y You can set either
or if the model
does not support airow direction settings.
Prhbt Set whether to allow or prohibit use of the local
remote controller. 1) Touch [Prhbt]. 2)
Use
to select from “Accept”,
“Prhbt1”, “Prhbt2”, “Prhbt3”, or “Prhbt4”. Accept: Allows operations with the remote controller. Prhbt1 to Prhbt4: Operations on the remote controller are restricted. You can change the restricted operations. (P.185)
EnerSavStg Enable or disable energy saving operation.
1) Touch [EnerSavStg]. 2) Select “Valid” or “Invl”.
Note
y You do not have to set all items, but “Time” must be set. y You can register up to 50 setting cells per day for a single
indoor unit or single schedule group.
y When setting schedule groups, you can only set those
items that are common to the indoor units that make up the group.
Continued on next page
Setting a schedule
45
Setting a schedule
Operation/Status
9
Touch [Register].
z A conrmation message appears. z To cancel the settings, touch [Cancel].
9
10
Touch [OK].
z The setting is registered. z The conrmation message “Change sched. for the next
day to 4 days later?” may be displayed. To overwrite the setting touch [OK]. To change, touch [Cancel].
Note
y Indoor units or schedule groups whose setting cells are all
blank will not run at all.
(3) Touch [Register].
z The settings are registered and the “Sttg” dialogue closes. z To cancel the settings, touch [Cancel].
6-
3
7
Touch [Register].
z The “Detail setting” dialogue closes. z To cancel the settings, touch [Cancel].
7
8
Repeat steps 4 to 7 to register other indoor units.
z Repeat steps 3 to 7 if you want to register in other daily
running modes.
z The conrmation message “Change sched. for the next
day to 4 days later?” may be displayed. To overwrite the setting touch [OK]. To change, touch [Cancel].
Setting a schedule
TGR-318_ENG.indb 68 2017/04/06 10:43:05