Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 145
[2K] Switches to EDID corresponding to the 2K image signal (maximum 1 920 x 1 200 dots) or lower.
Note
f Switch the setting to [4K/30p] when proper image is not projected while [EDID SELECT] is set to [4K/60p/HDR] or [4K/60p/SDR] and the 4K
image signal is input.
f Switch the setting to [2K] when proper image is not projected while [EDID SELECT] is set to [4K/60p/HDR], [4K/60p/SDR], or [4K/30p] and
the 2K image signal or lower is input.
f For details of the signal described in EDID of [4K/60p/HDR], [4K/60p/SDR], [4K/30p], or [2K], refer to “List of plug and play compatible
signals” (x page 329).
Setting [EDID MODE] in [HDMI IN]
1) Press as to select [HDMI IN].
2) Press the <ENTER> button.
f The [HDMI IN] screen is displayed.
3) Press as to select [HDMI1] or [HDMI2], and press the <ENTER> button.
f The [HDMI1] screen or the [HDMI2] screen is displayed.
4) Press as to select [EDID MODE].
5) Press the <ENTER> button.
f The [HDMI EDID MODE] screen is displayed.
6) Press qw to switch the item.
f The items will switch each time you press the button.
[DEFAULT] Standard setting.
[SCREEN FIT]
*1
Changes the EDID data according to the [SCREEN FORMAT] setting.
[USER] Sets the [RESOLUTION] and [VERTICAL SCAN FREQUENCY] items as EDID.
*1 PT-RZ24K and PT-RZ17K only
f Proceed to Step 11) when [DEFAULT] or [SCREEN FIT] is selected.
7) Press the <ENTER> button.
f The [RESOLUTION] screen is displayed.
8) Press asqw to select [RESOLUTION].
f Select [1024x768p], [1280x720p], [1280x800p], [1280x1024p], [1366x768p], [1400x1050p], [1440x900p],
[1600x900p], [1600x1200p], [1680x1050p], [1920x1080p], [1920x1080i], [1920x1200p], [2048x1080p],
[2560x1440p], [2560x1600p], or [3840x2400p].
9) Press the <ENTER> button.
f The [VERTICAL SCAN FREQUENCY] screen is displayed.
10) Press qw to select [VERTICAL SCAN FREQUENCY].
f Select [60Hz], [50Hz], or [30Hz] when [3840x2400p] is selected for [RESOLUTION].
f Select [60Hz], [50Hz], [30Hz], [25Hz], or [24Hz] when [2048x1080p] is selected for [RESOLUTION].
f Select [120Hz], [60Hz], [50Hz], [30Hz], [25Hz], or [24Hz] when [1920x1080p] is selected for
[RESOLUTION].
f Select [60Hz], [50Hz], or [48Hz] when [1920x1080i] is selected for [RESOLUTION].
f Select [60Hz] or [50Hz] when anything other than following is selected for [RESOLUTION].
g [3840x2400p], [2048x1080p], [1920x1080p], [1920x1080i]
11) Press the <ENTER> button.
f The conrmation screen is displayed.
12) Press qw to select [OK], and press the <ENTER> button.
Note
f The settings in [RESOLUTION] and [VERTICAL SCAN FREQUENCY] are displayed in [EDID STATUS].
f The resolution and vertical scanning frequency settings may also be required on your computer or video device.
f The computer, video device, or projector in use may require the power to be turned off and on again after conguring settings.
To Next Page
Loading...
