Parker TPDM - Page 122

Parker Hannifin Manufacturing Srl user’s manual TPDM
121
Binary parameters of the pico-PLC
Par.
Description
Def.
Type
Note
b90.0
Status of digital input 0. Status of digital input 1.This input is
commononly for the axisenabled: bit b230.1=1.
0
R/W
b90.1
Status of digital input 1. Status of digital input 2. This input is
commononly for the axis enabled: bit b230.1=1.
0
R/W
b90.2
Status of digital input 2. Status of digital input 3.This input is
commononly for the axis enabled: bit b230.1=1.
0
R/W
b90.3
Status of digital input 3. Status of digital input 4.This input is
commononly for the axis enabled: bit b230.1=1.
0
R/W
b90.4
Bit that can be stored.If the bit b230.1=0 this is a bit that can be
stored by the user. Otherwise,Status of digital input 4 if the bit
b230.1=1,this input is commonfor the axis enabled (only TPDM multi
axis).
0
R/W
b90.5
Bit that can be stored.If the bit b230.1=0 this is a bit that can be
stored by the user. Otherwise, Status of digital input 5 if the bit
b230.1=1,this input is commonfor the axis enabled (only TPDM multi
axis).
0
R/W
b90.6
Bit that can be stored.If the bit b230.1=0 this is a bit that can be
stored by the user. Otherwise, Status of digital input 6 if the bit
b230.1=1,this input is commonfor the axis enabled (only TPDM multi
axis).
0
R/W
b90.7
Bit that can be stored.If the bit b230.1=0 this is a bit that can be
stored by the user. Otherwise, Status of digital input7 if the bit
b230.1=1,this input is commonfor the axis enabled (only TPDM multi
axis).
0
R/W
b90.8
Bit that can be stored.If the bit b230.1=0 this is a bit that can be
stored by the user. Otherwise, Status of digital input 8 if the bit
b230.1=1,this input is commonfor the axis enabled (only TPDM multi
axis).
0
R/W
b90.9
Bit that can be stored.If the bit b230.1=0 this is a bit that can be
stored by the user. Otherwise, Status of digital input 9 if the bit
b230.1=1,this input is commonfor the axis enabled (only TPDM multi
axis).
0
R/W
b90.10
Bit that can be stored.If the bit b230.1=0 this is a bit that can be
stored by the user. Otherwise, Status of digital input 10 if the bit
b230.1=1,this input is commonfor the axis enabled (only TPDM multi
axis).
0
R/W
b90.11
Bit that can be stored.If the bit b230.1=0 this is a bit that can be
stored by the user. Otherwise, Status of digital input 11 if the bit
b230.1=1,this input is commonfor the axis enabled (only TPDM multi
axis).
0
R/W
b90.12
Status of motor brake unit. (1) 24V on brake.
0
R/W
b90.X
Bit that can be stored.If X is greater than 12 (only TPDM multi
axis).This is a bit that can be stored by the user.
0
R/W
M
b91.0
Status of digital output 0. Status of digital output 0.
0
R/W
b91.1
Status of digital output 1. Status of digital output 1.
0
R/W
b91.2
Motor brake command. Command to open(1)/close(0) the motor
brake
0
R/W