Rohde & Schwarz CMW500 - Default Chapter; Status:operation:task:a:<Netw_Std>:<Func_Grp>:<Appl>:Xcondition; Status:operation:task:a:<Netw_Std>:<Func_Grp>:Xcondition; Status:operation:task:a:<Netw_Std>:Xcondition

Command Reference - Base Software
R&S
®
CMW500
267User Manual 1173.9463.02 ─ 06
STATus:OPERation:TASK:A:<netw_std>:XWCondition?....................................................270
STATus:OPERation:TASK:A:<netw_std>:<func_grp>:XWCondition?..................................270
STATus:OPERation:TASK:A:<netw_std>:<func_grp>:<appl>:XWCondition?........................270
STATus:OPERation:XWEVent?.......................................................................................270
STATus:OPERation:TASK:XWEVent?.............................................................................270
STATus:OPERation:TASK:A:XWEVent?..........................................................................270
STATus:OPERation:TASK:A:<netw_std>:XWEVent?.........................................................270
STATus:OPERation:TASK:A:<netw_std>:<func_grp>:XWEVent?.......................................271
STATus:OPERation:TASK:A:<netw_std>:<func_grp>:<appl>:XWEVent?.............................271
STATus:OPERation:XCONdition?
STATus:OPERation:TASK:XCONdition?
STATus:OPERation:TASK:A:XCONdition?
STATus:OPERation:TASK:A:<netw_std>:XCONdition?
STATus:OPERation:TASK:A:<netw_std>:<func_grp>:XCONdition?
STATus:OPERation:TASK:A:<netw_std>:<func_grp>:<appl>:XCONdition?
Returns the contents of the CONDition part of the status register, see Structure of an
SCPI Status Register. Reading the CONDition registers is nondestructive.
For a description of the variables <netw_std>, <func_grp> and <appl> refer to table 6-1.
Return values:
<List> Comma separated list of mnemonics (and/or decimal numbers
between 0 and 65535) enclosed in brackets
Example:
STAT:OPER:TASK:A:GPRF:GEN:UNIV:XCON?
Query the CONDition part of the status register for the GPRF gen-
erator. The result is (OFF) or (PEND) or (ON).
Usage: Query only
Firmware/Software: V2.0.10
STATus:OPERation:XENable <List>
STATus:OPERation:TASK:XENable <List>
STATus:OPERation:TASK:A:XENable <List>
STATus:OPERation:TASK:A:<netw_std>:XENable <List>
STATus:OPERation:TASK:A:<netw_std>:<func_grp>:XENable <List>
STATus:OPERation:TASK:A:<netw_std>:<func_grp>:<appl>:XENable <List>
Sets the enable mask which allows true conditions in the EVENt part of the status register
to be reported in the summary bit. If a bit is 1 in the enable register and its associated
event bit transitions to true, a positive transition will occur in the summary bit reported to
the next higher level. See also Structure of an SCPI Status Register.
For a description of the variables <netw_std>, <func_grp> and <appl> refer to table 6-1.
Parameters:
<List> Comma separated list of mnemonics (and/or decimal numbers
between 0 and 65535) enclosed in brackets
Instrument-Control Commands