Rohde & Schwarz PR100 - Measurement Subsystem; Format Subsystem; Input Subsystem; Memory Subsystem

R&S PR100 User Manual
Waterfall signal level range WAT:CMAP:RANG 60.0 10.0 140.0 dB + -
Waterfall signal level threshold WAT:CMAP:THR 50 -30 110 dBµV + -
Waterfall hold WAT:HOLD 1 0 1 bool + -
Waterfall speed WAT:SPEE 20 lines/s + -
Window mode WIND RX+Spectrum enum + -
13.2 FORMat subsystem
Item Command [FORM:] Factory
Default
Min Max Unit *RST PWR
ON
Binary data byte order BORD NORM NA NA NA + +
Binary output data format DATA ASC NA NA NA + +
Binary memory data format MEM ASC NA NA NA + +
Status register data format SREG ASC NA NA NA + +
13.3 INPut subsystem
Item Command [INP:] Factory
Default
Min Max Unit *RST PWR
ON
Input attenuation ATT 0 0 1 bool + -
13.4 MEASurement subsystem
Item Command [MEAS:] Factory
Default
Min Max Unit *RST PWR
ON
Measurement Mode MODE CONT None None enum + -
Measurement Time TIME DEF 0.5m 900 s + -
13.5 MEMory subsystem
Item Command: [MEM:] Factory
Default
Min Max Unit *RST PWR
ON
First memory save location SAVE:AUTO:STAR 800 0 1023 + -
Last memory save location SAVE:AUTO:STOP 999 0 1023 + -
First mem save location direct SAVE:DIR:STAR 600 0 1023 + -
Last mem save location direct SAVE:DIR:STOP 799 0 1023 + -
13.6 OUTPut subsystem
Item Command: [OUTP:] Factory
Default
Min Max Unit *RST PWR
ON
antenna selection bits BITA:STAT 0 - - - + -
Antenna selection bits BYTA:STAT 0 - - - + -
IF state IF:STAT 0 - - bool + -
Squelch from memory SQU:CONT NONE - - enum + -
Squelch state SQU:STAT 0 - - bool + -
Squelch autosave SQU:STOR 0 - - bool + -
Squelch threshold SQU:THR 0.0 -30.0 110.0 dBµV + -
Tone control TONE:CONT ONLY - - enum + -
Tone gain TONE:GAIN - - - oct/dB + -
Tone state TONE:STAT 0 - - bool + -
Tone threshold TONE:THR 0.0 -14.0 94.0 dBµV + -
13.7 SENSe subsystem
Item Command: [SENS:] Factory
Default
Min Max Unit *RST PWR
ON
Current IF bandwidth BAND 150k 150 500k Hz + -
Selected antenna correction CORR:ANT PASS - - enum + -
Demodulation type DEM FM - - enum + -
Beat frequency DEM:BFO:FREQ 1k -8k 8k Hz + -
Detector function DET PEAK - - enum + -
AFC function FREQ:AFC 0 - - bool + -
Frequency conversion threshold FREQ:CONV:THR 25M 9k 30M Hz + -
RX frequency FREQ 100M 9k 7.5G Hz + -
Receiver mode FREQ:MODE CW - - enum + -
PSCAN frequency center FREQ:PSC:CENT - - - - + -
PSCAN frequency span FREQ:PSC:SPAN - - - - + -
PSCAN frequency start FREQ:PSC::STAR 88M 9K 100G Hz + -
PSCAN frequency stop FREQ:PSC::STOP 108M 9K 100G Hz + -