Roland RD-2000 Parameter Guide

44
Modulation FX Parameters
Parameter Value Explanation
Feedback
Knob
OFF,
RATE,
DEPTH,
MOD WAVE
Species the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.
Mod Wave
TRI,
SQR,
SIN,
SAW1,
SAW2
Modulation wave
TRI: triangle wave
SQR: square wave
SIN: sine wave
SAW1/2: sawtooth wave
SAW1 SAW2
R R
L L
Rate
(sync sw)
OFF, ON
If this is ON, the modulation
is synchronized to the tempo
of the rhythm (owner’s
manual: p. 24).
Rate (Hz) #/
Rate (note) #
0.05–10.00 [Hz]
Frequency of the change
note (p. 60)
Depth # 0–127
Depth to which the eect is
applied
Low Gain -15–+15 [dB] Gain of the low range
High Gain -15–+15 [dB] Gain of the high range
Level 0–127 Output Level
25: SLICER
By applying successive cuts to the sound, this eect turns a
conventional sound into a sound that appears to be played as a
backing phrase. This is especially eective when applied to sustain-
type sounds.
L in
R in
L out
R out
Slicer
Slicer
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.
Depth Knob
RATE,
ATTACK,
SHUFFLE
Species the parameter
that is controlled by the
MODULATION FX [DEPTH]
knob.
Rate Knob
Species the parameter
that is controlled by the
MODULATION FX [RATE]
knob.
Feedback
Knob
OFF,
RATE,
ATTACK,
SHUFFLE
Species the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.
Step 01–16 0–127 Level at each step
Rate
(sync sw)
OFF, ON
If this is ON, the modulation
is synchronized to the tempo
of the rhythm (owner’s
manual: p. 24).
Rate (Hz) #/
Rate (note) #
0.05–10.00 [Hz]
Rate at which the 16-step
sequence will cycle
note (p. 60)
Attack # 0–127
Speed at which the level
changes between steps
Parameter Value Explanation
Input Sync
Sw
OFF, ON
Species whether an input
note will cause the sequence
to resume from the rst step
of the sequence (ON) or not
(OFF)
Input Sync
Threshold
0–127
Volume at which an input
note will be detected
Mode
LEGATO,
SLASH
Sets the manner in which the
volume changes as one step
progresses to the next.
LEGATO: The change in
volume from one step’s
level to the next remains
unaltered. If the level of a
following step is the same as
the one preceding it, there is
no change in volume.
SLASH: The level is
momentarily set to 0 before
progressing to the level of
the next step. This change
in volume occurs even if the
level of the following step is
the same as the preceding
step.
Shue # 0–127
Timing of volume changes
in levels for even-numbered
steps (step 2, step 4, step 6...).
The higher the value, the
later the beat progresses.
Level 0–127 Output level
26: CHORUS
This is a stereo chorus. A lter is provided so that you can adjust the
timbre of the chorus sound.
L in
R in
Chorus
Chorus
L out
R out
2-Band
EQ
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.
Depth Knob
RATE,
BALANCE,
DEPTH
Species the parameter
that is controlled by the
MODULATION FX [DEPTH]
knob.
Rate Knob
Species the parameter
that is controlled by the
MODULATION FX [RATE]
knob.
Feedback
Knob
OFF,
RATE,
BALANCE,
DEPTH
Species the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.

Roland RD-2000 Specifications

General

Pedal jack	Yes
Sound effects	Compression, Equalization, Modulation, Reverberation
Tones quantity	1100
Built-in speaker(s)	No
Number of front panel sliders	9
Reverberation effects quantity	6
Preset programs quantity	300
Keyboard name	PHA-50
Keys quantity	88 keys
Display resolution	256 x 80 pixels
Power consumption (max)	23 W
Audio (L/R) out	2
Headphone outputs	1
USB connector type	USB Type-A, USB Type-B
Headphone connectivity	6.3 mm
Product color	Black
Cables included	AC

Weight and Dimensions

Depth	367 mm
Width	1412 mm
Height	140 mm
Weight	21700 g