Roland RD-2000 Parameter Guide

53
Modulation FX Parameters
Parameter Value Explanation
Delay Time
(msec) #/
Delay Time
(note) #
1–1300 [msec]
Adjusts the time until the
delay is heard.
note (p. 60)
Acceleration 0–15
Adjusts the speed which the
Delay Time changes from the
current setting to a specied
new setting.
The rate of change for the
Delay Time directly aects
the rate of pitch change.
Feedback # -98–+98 [%]
Adjusts the amount of the
delay sound that’s fed back
into the eect. Negative “-”
settings invert the phase.
HF Damp
200–8000 [Hz],
BYPASS
Adjusts the frequency above
which sound fed back to
the eect is ltered out
(BYPASS: no cut).
Low Gain -15–+15 [dB]
Gain of the low frequency
range
High Gain -15–+15 [dB]
Gain of the high frequency
range
Balance #
D100:0W–
D0:100W
Volume balance between
the direct sound (D) and the
delay sound (W)
Level 0–127 Output Level
45: LOFI COMPRESS
This is an eect that intentionally degrades the tone quality for
creative purposes.
L in
R in
L out
R out
Compressor
Lo-Fi
Lo-Fi
Compressor
2-Band
EQ
2-Band
EQ
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.
Depth Knob
BALANCE,
LEVEL
Species the parameter
that is controlled by the
MODULATION FX [DEPTH]
knob.
Rate Knob
Species the parameter
that is controlled by the
MODULATION FX [RATE]
knob.
Feedback
Knob
OFF,
BALANCE,
LEVEL
Species the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.
Pre Filter
Type
1–6
Selects the type of lter
applied to the sound before
it passes through the Lo-Fi
eect.
1: Compressor o
2–6: Compressor on
LoFi Type 1–9
Degrades the tone quality.
The tone quality grows
poorer as this value is
increased.
Parameter Value Explanation
Post Filter
Type
OFF, LPF, HPF
Type of lter
OFF: no lter is used
LPF: cuts the frequency
range above the Cuto
HPF: cuts the frequency
range below the Cuto
Post Filter
Cuto
200–8000 [Hz]
Basic frequency of the Post
Filter
Low Gain -15–+15 [dB] Gain of the low range
High Gain -15–+15 [dB] Gain of the high range
Balance #
D100:0W–
D0:100W
Volume balance between
the direct sound (D) and the
eect sound (W)
Level # 0–127 Output Level
46: BIT CRUSHER
This creates a lo- sound.
L in
R in
L out
R out
Bit Crusher
2-Band EQ
2-Band EQ
Bit Crusher
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.
Depth Knob
SAMPLE RATE,
BIT DOWN,
FILTER
Species the parameter
that is controlled by the
MODULATION FX [DEPTH]
knob.
Rate Knob
Species the parameter
that is controlled by the
MODULATION FX [RATE]
knob.
Feedback
Knob
OFF,
SAMPLE RATE,
BIT DOWN,
FILTER
Species the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.
Sample Rate
#
0–127 Adjusts the sample rate.
Bit Down # 0–20 Adjusts the bit depth.
Filter # 0–127 Adjusts the lter depth.
Low Gain -15–+15 [dB]
Gain of the low frequency
range
High Gain -15–+15 [dB]
Gain of the high frequency
range
Level 0–127 Output Level
47: PITCH SHIFTER
A stereo pitch shifter.
L in
R in
Pitch Shifter
Pitch Shifter
L out
R out
2-Band EQ
2-Band EQ
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.

Roland RD-2000 Specifications

General

Pedal jack	Yes
Sound effects	Compression, Equalization, Modulation, Reverberation
Tones quantity	1100
Built-in speaker(s)	No
Number of front panel sliders	9
Reverberation effects quantity	6
Preset programs quantity	300
Keyboard name	PHA-50
Keys quantity	88 keys
Display resolution	256 x 80 pixels
Power consumption (max)	23 W
Audio (L/R) out	2
Headphone outputs	1
USB connector type	USB Type-A, USB Type-B
Headphone connectivity	6.3 mm
Product color	Black
Cables included	AC

Weight and Dimensions

Depth	367 mm
Width	1412 mm
Height	140 mm
Weight	21700 g