Roland RD-2000 - Reverse Delay; Time Ctrl Delay

52
Modulation FX Parameters
Parameter Value Explanation
Delay 1–4
Level
0–127 Output level of Delays 1–4
Low Gain -15–+15 [dB]
Gain of the low frequency
range
High Gain -15–+15 [dB]
Gain of the high frequency
range
Balance #
D100:0W–
D0:100W
Volume balance between
the direct sound (D) and the
eect sound (W)
Level 0–127 Output Level
43: REVERSE DELAY
This is a reverse delay that adds a reversed and delayed sound to
the input sound. A tap delay is connected immediately after the
reverse delay.
Feedback
L in
R in
Rev. Delay
L out
R out
2-Band
EQ
2-Band
EQ
Rev
Delay
D2
D1
D3
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.
Depth Knob
REV DLY
FEEDBACK,
DLY 3 FEEDBACK,
BALANCE
Species the parameter
that is controlled by the
MODULATION FX [DEPTH]
knob.
Rate Knob
Species the parameter
that is controlled by the
MODULATION FX [RATE]
knob.
Feedback
Knob
OFF,
REV DLY
FEEDBACK,
DLY 3 FEEDBACK,
BALANCE
Species the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.
Threshold 0–127
Volume at which the reverse
delay will begin to be applied
Rev Delay
Time
(sync sw)
OFF, ON
If this is ON, the modulation
is synchronized to the tempo
of the rhythm (owner’s
manual: p. 24).
Rev Delay
Time (msec)/
Rev Delay
Time (note)
1–1300 [msec]
Delay time from when sound
is input into the reverse delay
until the delay sound is heard
note (p. 60)
Rev Delay
Feedback #
-98–+98 [%]
Proportion of the delay
sound that is to be returned
to the input of the reverse
delay (negative values invert
the phase)
Rev Delay HF
Damp
200–8000 [Hz],
BYPASS
Frequency at which the high-
frequency content of the
reverse-delayed sound will
be cut (BYPASS: no cut).
Rev Delay
Pan
L64–63R
Panning of the reverse delay
sound
Rev Delay
Level
0–127
Volume of the reverse delay
sound
Parameter Value Explanation
Delay
1–3 Time
(sync sw)
OFF, ON
If this is ON, the modulation
is synchronized to the tempo
of the rhythm (owner’s
manual: p. 24).
Delay 1–3
Time (msec)/
Delay 1–3
Time (note)
1–1300 [msec]
Delay time from when sound
is input into the tap delay
until the delay sound is heard
note (p. 60)
Delay 3
Feedback #
-98–+98 [%]
Proportion of the delay
sound that is to be returned
to the input of the tap delay
(negative values invert the
phase)
Delay HF
Damp
200–8000 [Hz],
BYPASS
Frequency at which the
low-frequency content of the
tap delay sound will be cut
(BYPASS: no cut).
Delay 1 Pan,
Delay 2 Pan
L64–63R
Panning of the tap delay
sounds
Delay 1 Level,
Delay 2 Level
0–127
Volume of the tap delay
sounds
Low Gain -15–+15 [dB]
Gain of the low frequency
range
High Gain -15–+15 [dB]
Gain of the high frequency
range
Balance #
D100:0W–
D0:100W
Volume balance of the
original sound (D) and delay
sound (W)
Level 0–127 Output Level
44: TIME CTRL DELAY
A stereo delay in which the delay time can be varied smoothly.
R in
R out
L in
L out
Feedback
Feedback
Balance W
Balance W
Time Ctrl Delay
Time Ctrl Delay
2-Band EQ
2-Band EQ
Balance D
Balance D
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.
Depth Knob
DELAY TIME,
FEEDBACK,
BALANCE
Species the parameter
that is controlled by the
MODULATION FX [DEPTH]
knob.
Rate Knob
Species the parameter
that is controlled by the
MODULATION FX [RATE]
knob.
Feedback
Knob
OFF,
DELAY TIME,
FEEDBACK,
BALANCE
Species the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.
Delay Time
(sync sw) #
OFF, ON
If this is ON, the modulation
is synchronized to the tempo
of the rhythm (owner’s
manual: p. 24).