EasyManuals Logo

Roland RD-2000 Parameter Guide

Roland RD-2000
83 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #45 background imageLoading...
Page #45 background image
45
Modulation FX Parameters
Parameter Value Explanation
Filter Type
OFF,
LPF,
HPF
Type of lter
OFF: no lter is used
LPF: cuts the frequency
range above the Cuto Freq
HPF: cuts the frequency
range below the Cuto Freq
Cuto Freq 200–8000 [Hz] Basic frequency of the lter
Pre Delay 0.0–100 [msec]
Adjusts the delay time from
the direct sound until the
chorus sound is heard.
Rate
(sync sw)
OFF, ON
If this is ON, the modulation
is synchronized to the tempo
of the rhythm (owner’s
manual: p. 24).
Rate (Hz) #/
Rate (note) #
0.05–10.00 [Hz]
Frequency of modulation
note (p. 60)
Depth 0–127 Depth of modulation
Phase 0–180 [deg] Spatial spread of the sound
Low Gain -15–+15 [dB] Gain of the low range
High Gain -15–+15 [dB] Gain of the high range
Balance #
D100:0W–
D0:100W
Volume balance between
the direct sound (D) and the
chorus sound (W)
Level 0–127 Output Level
27: FLANGER
This is a stereo anger. (The LFO has the same phase for left and
right.) It produces a metallic resonance that rises and falls like a jet
airplane taking o or landing. A lter is provided so that you can
adjust the timbre of the anged sound.
R in
R out
L in
L out
Flanger
Feedback
Feedback
Flanger
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.
Depth Knob
RATE,
FEEDBACK,
BALANCE
Species the parameter
that is controlled by the
MODULATION FX [DEPTH]
knob.
Rate Knob
Species the parameter
that is controlled by the
MODULATION FX [RATE]
knob.
Feedback
Knob
OFF,
RATE,
FEEDBACK,
BALANCE
Species the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.
Filter Type
OFF,
LPF,
HPF
Type of lter
OFF: no lter is used
LPF: cuts the frequency
range above the Cuto Freq
HPF: cuts the frequency
range below the Cuto Freq
Parameter Value Explanation
Cuto Freq 200–8000 [Hz] Basic frequency of the lter
Pre Delay 0.0–100 [msec]
Adjusts the delay time from
the direct sound until the
anger sound is heard.
Rate
(sync sw)
OFF, ON
If this is ON, the modulation
is synchronized to the tempo
of the rhythm (owner’s
manual: p. 24).
Rate (Hz) #/
Rate (note) #
0.05–10.00 [Hz]
Frequency of modulation
note (p. 60)
Depth 0–127 Depth of modulation
Phase 0–180 [deg] Spatial spread of the sound
Feedback # -98–+98 [%]
Adjusts the proportion of the
anger sound that is fed back
into the eect. Negative “-”
settings will invert the phase.
Low Gain -15–+15 [dB] Gain of the low range
High Gain -15–+15 [dB] Gain of the high range
Balance #
D100:0W–
D0:100W
Volume balance between
the direct sound (D) and the
anger sound (W)
Level 0–127 Output Level
28: STEP FLANGER
This is a anger in which the anger pitch changes in steps. The
speed at which the pitch changes can also be specied in terms of
a note-value of a specied tempo.
R in
R out
L in
L out
Feedback
Feedback
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
Step Flanger
Step Flanger
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.
Depth Knob
RATE,
FEEDBACK,
STEP RATE,
BALANCE
Species the parameter
that is controlled by the
MODULATION FX [DEPTH]
knob.
Rate Knob
Species the parameter
that is controlled by the
MODULATION FX [RATE]
knob.
Feedback
Knob
OFF,
RATE,
FEEDBACK,
STEP RATE,
BALANCE
Species the parameter
that is controlled by the
MODULATION FX [FEEDBACK]
knob.
Filter Type
OFF,
LPF,
HPF
Type of lter
OFF: no lter is used
LPF: cuts the frequency
range above the Cuto Freq
HPF: cuts the frequency
range below the Cuto Freq
Cuto Freq 200–8000 [Hz] Basic frequency of the lter

Table of Contents

Other manuals for Roland RD-2000

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Roland RD-2000 and is the answer not in the manual?

Roland RD-2000 Specifications

General IconGeneral
Pedal jackYes
Sound effectsCompression, Equalization, Modulation, Reverberation
Tones quantity1100
Built-in speaker(s)No
Number of front panel sliders9
Reverberation effects quantity6
Preset programs quantity300
Keyboard namePHA-50
Keys quantity88 keys
Display resolution256 x 80 pixels
Power consumption (max)23 W
Audio (L/R) out2
Headphone outputs1
USB connector typeUSB Type-A, USB Type-B
Headphone connectivity6.3 mm
Product colorBlack
Cables includedAC
Weight and Dimensions IconWeight and Dimensions
Depth367 mm
Width1412 mm
Height140 mm
Weight21700 g

Related product manuals