Home
Servomex
Measuring Instruments
SERVOFLEX MiniMP
Servomex SERVOFLEX MiniMP User Manual
4
of 1
of 1 rating
104 pages
Give review
Manual
Specs
To Previous Page
To Previous Page
Loading...
5200 Multi Pur
pose and 5200 Multi Pur
pose HF Gas Analysers
05230001A / Revision 9
98
This page intentionally blank.
103
Table of Contents
Default Chapter
3
Table of Contents
3
1 Description and Definitions
7
Scope of this Manual
7
Safety Information
7
Description
7
Sample Measurement Configurations
8
Other Product Options
8
2 Specification
11
General
11
Sample Gas
12
Calibration Gases
13
Environmental Limits
14
Performance: Standard Oxygen Sensor
15
Performance: Industrial Oxygen Sensor (Standard Multi Purpose Only)
16
Performance: High Accuracy Oxygen Sensor
17
Performance: IR (Infrared) Sensors
18
Rechargeable Battery (Optional Feature)
19
Milliamp Outputs (Optional Feature)
19
3 Unpack the Multi Purpose
20
4 Multi Purpose User Interface
21
Introduction
21
Start-Up and Measurement Screens
21
Soft Key Legends
23
Status Icon Bar
24
Scroll Bars
25
Menu Options/Screens and Password Protection
25
The Menu Screen
27
The Settings Screen
28
The Information Screen
28
Editing On-Screen Data
29
5 Installation and Set-Up
30
Installation and Switch-On
30
Charging/Recharging the Battery (Multi Purpose with Optional Rechargeable Battery)
32
Charging
32
Recharging
32
Multi Purpose Set-Up
33
Selecting the Security Level and Changing the Password(S)
33
Setting the Clock
36
Changing Regional Settings
37
Selecting Power Save Mode (Multi Purpose with Optional Rechargeable Battery)
38
Selecting Pump Operation (Multi Purpose HF or Standard Multi Purpose with Optional Internal Sample Pump)
39
6 General Operation
41
Calibrating the Multi Purpose
41
Taking Sample Readings
44
Correcting Oxygen Measurement for Different Background Gases
45
Overview of Measurement Errors
45
Entering a Cross-Interference Compensation
45
Selecting Display Units
47
Configuring the Measurement Alarms
49
Alarm Modes and Levels
49
Latching/Non-Latching Alarms
49
Hysteresis Levels
50
Setting the Measurement Alarm Levels and Modes
51
Enabling/Disabling the Audible Measurement Alarm
52
Silencing (Muting) the Audible Measurement Alarm
52
Unlatching Measurement Alarms
53
Viewing the Measurement Alarm Status
53
Configuring and Using the Milliamp Outputs (Optional Feature)
54
Overview
54
Introduction to the Milliamp Output Parameters
55
Set up the Milliamp Output Parameters
56
Select the Range Associated with a Measurement
57
Calibrate a Milliamp Output
58
Check a Milliamp Output
59
Data Logging, Serial Outputs and Printed Outputs
60
Selecting Data Logging/Serial Output/Printed Outputs
60
Configuring the Serial Output Parameters
61
Introduction to Data Logging
62
Entering Measurement Data into the Data Log
62
Starting a New Data Log Batch
63
Outputting the Data Log
63
Viewing the Data Log
64
Clearing the Data Log
64
Printing a Sample Measurement Report
65
Adjusting the Display
65
Adjusting the Backlight Timer
65
Adjusting the Contrast
66
Switching off the Multi Purpose after Use
66
7 Routine Maintenance
67
Cleaning the Multi Purpose
67
Inspecting the Inlet Filter Element
67
Regenerate/Replace the Drying Agent
68
Use of the Multi Purpose for Carbon Monoxide Measurements
69
Preventative Maintenance
70
8 Fault Finding
71
Introduction to Faults and Fault Messages
71
Viewing Fault Messages
74
General Fault Finding
74
9 Storage and Disposal
80
Storage
80
Disposal
80
10 Spares
81
A1 Data Log Output Formats
82
A2 Serial Output Formats
84
A3 Printer Output Formats
85
A4 Rs232 Connection Details
87
A4.1 Overview
87
A4.2 Connecting the Multi Purpose to a PC
87
A4.3 Capturing Data Using Windows® and Hyper Terminal
88
A5 Display Unit Conversion Factors
89
A6 Optional Flowmeters
90
A6.1 Overview
90
A6.2 Specification
90
A6.3 Preparing the Multi Purpose with a Flowmeter
90
A6.4 Using the Multi Purpose with a Flowmeter
92
A6.5 Multi Purpose HF and Standard Multi Purpose
92
With a Sample Pump
92
A6.6 Standard Multi Purpose Without a Sample Pump
92
A7 Optional Sample Conditioning Panel
93
A7.1 Overview
93
A7.2 Specification
93
A7.3 Using the Multi Purpose with the Sample Conditioning Panel
94
A7.4 Calibrating
94
A7.5 Sampling Gases
94
A7.6 Additional Maintenance
96
A7.7 Draining the Catchpot
96
A7.8 Replacing/Regenerating the Drying Agent
96
A7.9 Additional Spares
97
A8.1
98
A8.2
98
A8.3
98
A8.4
98
A8.5
98
Optional Gas Probe Accessory
98
Overview
98
Preparing for Use
98
Using the Probe
98
Additional Maintenance
98
Additional Spares
99
Materials in Contact with Sample and Calibration Gases
100
Disposal in Accordance with the Waste Electrical and Electronic Equipment (Weee) Directive
102
Compliance and Standards Information
103
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Servomex SERVOFLEX MiniMP and is the answer not in the manual?
Ask a question
Servomex SERVOFLEX MiniMP Specifications
General
Brand
Servomex
Model
SERVOFLEX MiniMP
Category
Measuring Instruments
Language
English
Related product manuals
Servomex SERVOPRO FID
67 pages
Servomex SERVOPRO 4100
74 pages
Servomex SERVOTOUGH Oxy
145 pages
Servomex SERVO PRO 14440D1
38 pages
Servomex SERVOPRO MultiExact
145 pages
Servomex SERVOPRO 4000 Series
74 pages
Servomex 2700
40 pages
Need help?
General
To Previous Page
