Siemens SIMOCODE pro User Manual

Description of the blocks
4.1 Functions for all blocks
SIMOCODE pro PCS 7 Library V9.0
Programming and Operating Manual, 06/2017, A5E40899442002A/RS-AA/001
83
Example with a motor MMRevDhl:
In this case, use the interconnectable input parameters.
● FwdAut = 1 for the command "Start forward"
●
RevAut = 1 for the command "Start backwards"
●
StopAut = 1 for the stop command and
●
AutModLi = 1 for setting "Automatic" operating mode
●
ManModLi = 1 for setting "Manual" operating mode
Bit = 1:
Switching mode: two static automatic commands are assigned to a control input.
Example with a motor MMRevDhl:
In this case, use the interconnectable input parameters.
● FwdAut = 1 for the command "Start forward"
●
RevAut = 1 for the command "Start backwards" and
●
FwdAut = 0 and RevAut = 0 for the stop command
●
AutModLi = 1 for setting "Automatic" operating mode
●
AutModLi = 0 for setting "Manual" operating mode
The
StopAut and ManModLi control inputs are irrelevant in this case.
4.1.10.6
Set switching mode
Number of the Feature bit: 5
Feature bit purpose
Specify switching mode for the motor block.
The default setting is 0.
Bit = 0:
Switching mode "On over speed 1" with the SwOverTi > 0 parameter
Bit = 1:
Switching mode "Off over speed 1" with the SwOverTi > 0 parameter.
4.1.10.7
Enabling direct changeover between forward and reverse
Number of the Feature bit: 7
Feature bit purpose
Enable direct reversal of the direction of motors.
The default setting is 0.
Bit = 0:
Direct reversal of the direction is disabled.
You can only change the direction of the motor by first stopping and starting the motor again
in the required direction. The motor can only be started again after the time set in the
IdleTime parameter has elapsed.

Siemens SIMOCODE pro Specifications

General

Protection Class	IP20
Mounting Type	DIN rail mounting
Rated Operational Voltage	24 V DC
Rated Current	Up to 820 A
Protection Functions	Overload, short-circuit, phase failure, asymmetry, ground fault, motor stall
Operating Temperature Range	-25°C to +60°C
Communication Protocols	PROFIBUS DP, PROFINET, Modbus RTU
Analog Outputs	Up to 2
Temperature Monitoring	PTC/KTY, RTD (PT100/PT1000)
Digital Outputs	Relay outputs, Solid-state outputs
Analog Inputs	0/4-20mA, PT100/PT1000

Summary

Introduction

Security information

Discusses Siemens' commitment to industrial security and customer responsibilities.

Components of the software package

Lists the blocks and other components included in the SIMOCODE pro PCS 7 Library V9.0.

Configuration Steps

Details the procedures for configuring SIMOCODE pro devices in HW Config and CFC.

Driver generator

Explains the function and purpose of the driver generator for signal processing in PCS 7.

Parameterization softwares

Templates

Overview of the templates, control functions and blocks

Introduces templates for adopting control functions and lists associated blocks.

Using templates

Explains how to instantiate and interconnect templates within the SIMOCODE pro Library in CFC.

Block icons and faceplate views

Faceplates

Explains the structure, navigation, and views (Batch, Trend, Alarm, Preview) of SIMOCODE pro faceplates.

Description of the blocks

Functions for all blocks

Diagnostics block MMDiag

Details the MMDiag block's purpose, messages, and driver generator integration.

MMOprtn block

Provides an overview of the MMOprtn block, its purpose, views, and parameters.

Block for MMMeas measured value function

Describes the MMMeas block for gathering measured value parameters and diagnostic data.

Block for statistical function MMStat

Block for timestamping MMLog

MMRevDhl motor block

Covers the MMRevDhl block for controlling Dahlander High Feature reversing starters.

Parameter

MMDiag block parameter

Block parameter MMOprtn

Details input and output parameters for the MMOprtn block.

Block parameter MMMeas

Block parameter MMStat

Block parameter MMLog

Block parameter MMRevDhl

Details input and output parameters for the MMRevDhl block.