4-115
Siemens AG 2005 All Rights Reserved
SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition
Commissioning
4.1 General commissioning information 4-116. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Run–up of ”SIMODRIVE 611 universal” 4-119. . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 Commissioning via SimoCom U 4-120. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.1 First commissioning with SimoCom U 4-121. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2 Series commissioning with SimoCom U 4-122. . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.3 Password protection with SimoCom U (from SW 8.1) 4-123. . . . . . . . . . . . . . . . .
4.3.4 Automated firmware download (from SW 8.1) 4-126. . . . . . . . . . . . . . . . . . . . . . .
4.4 Commissioning using the display and operator unit 4-128. . . . . . . . . . . . . . . . . . .
4.5 Function–initiating and diagnostic parameters 4-131. . . . . . . . . . . . . . . . . . . . . . .
4.6 Parameters for hardware, operating mode and clock cycles 4-137. . . . . . . . . . .
4.7 Induction motor operation with induction motor 4-141. . . . . . . . . . . . . . . . . . . . . .
4.7.1 Description 4-141. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.7.2 Commissioning induction motors (ARM) without encoder 4-144. . . . . . . . . . . . .
4.7.3 Motor data optimization, steps 1 to 4 4-148. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.8 Permanent–magnet synchronous motor with field–weakening
(PE spindle) 4-153. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.8.1 Description 4-153. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.8.2 Commissioning 1FE1 motors 4-155. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.8.3 Current controller adaptation 4-160. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.8.4 Parameters for PE spindles 4-163. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.9 1FW6 build–in torque motors (from SW 6.1) 4-165. . . . . . . . . . . . . . . . . . . . . . . .
4.9.1 Description 4-165. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.9.2 Commissioning 1FW6 motors 4-167. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.9.3 Thermal motor protection 4-168. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.10 Linear motors (1FN1, 1FN3 motors) 4-169. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.10.1 General information on commissioning linear motors 4-169. . . . . . . . . . . . . . . . .
4.10.2 Commissioning: Linear motor with one primary section 4-172. . . . . . . . . . . . . . .
4.10.3 Commissioning: Linear motor with 2 identical primary sections 4-179. . . . . . . . .
4.10.4 Mechanical system 4-182. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.10.5 Thermal motor protection 4-184. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.10.6 Measuring system 4-188. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.10.7 Parallel and double–cam arrangement of linear motors 4-191. . . . . . . . . . . . . . .
4.10.8 Checking the linear motor by making measurements 4-192. . . . . . . . . . . . . . . . .
4.11 Direct measuring system for position control (from SW 3.3) 4-193. . . . . . . . . . .
4.12 Connecting induction motors with TTL encoder (from SW 8.1) 4-197. . . . . . . . .
4
To Next Page
Loading...
