Sony STR-DA2800ES - Page 143

STR-DA2800ES
143
Pin No. Pin Name I/O Description
1 GND - Ground terminal
2 C - External capacitor connection terminal
3 HDMI_REG_CONT O Power supply on/off control signal output terminal for HDMI section “H”: power on
4 SP_INT I Interrupt signal input from the HDMI transceiver
5 SP_RST O Reset signal output to the HDMI transceiver “L”: reset
6 ACDC_STOP I AC cut detection signal input terminal “H”: AC cut
7
HDMI_MON LPCM_
SUB
O Non-LPCM setting signal output terminal for HDMI audio Not used
8
HDMI_ERROR_OUT_
SUB
O HDMI error signal output terminal Not used
9 NC O Not used
10
HDMI_MON LPCM_
MAIN
O Non-LPCM setting signal output terminal for HDMI audio “H”: non-LPCM
11
HDMI_ERROR_OUT_
MAIN
O
HDMI error signal output to the main system controller “H”: error
Audio muting control signal output terminal
12 to 14 NC O Not used
15
VIDEO_UCOM_
ENDFLAG
O End fl ag signal output to the main system controller
16
UART_MAIN/VIDEO
(TX)
O Serial data output to the main system controller
17
UART_VIDEO/MAIN
(RX)
I Serial data input from the main system controller
18, 19 NC O Not used
20 INIT I Reset signal input from the main system controller “L”: reset
21 MD0 I Mode selection signal input from the main system controller “H”: writing mode
22 MD1 I Mode selection signal input terminal “H”: writing mode Fixed at “L” in this unit
23 XO O System clock output terminal (4 MHz)
24 XI I System clock input terminal (4 MHz)
25 VSS - Ground terminal
26 to 33 NC O Not used
34 UPDATE VIDEO/SEL O Update signal output to the audio/video signal decoder and RS232C connector
35 UPDATE SEL/VIDEO I Update signal input from the audio/video signal decoder and RS232C connector
36 UPDATE_SCK O Update clock signal output terminal
37 to 42
TEST_PIN0 to
TEST_PIN5
O Test control terminal
43 HDMI_RX1_5VPWR O Power supply on/off control signal output terminal for HDMI RX1 “H”: power on
44 HDMI_RX2_5VPWR O Power supply on/off control signal output terminal for HDMI RX2 “H”: power on
45 AVCC - Power supply terminal (+3.3V) (analog system)
46 AVRH I Reference voltage (+3.3V) input terminal (analog system)
47 AVSS - Ground terminal (analog system)
48, 49 NC O Not used
50 VSS - Ground terminal
51 VCC - Power supply terminal (+3.3V)
52 to 60 NC O Not used
61 (ADV7181_PWRDWN) O Power down signal output to the video A/D converter “L”: power down
62 ADV7181_RESET O Reset signal output to the video A/D converter “L”: reset
63 ADV7181_REG_CONT O Power supply on/off control signal output terminal for video A/D converter “H”: power on
64 ADV7181_INT I Interrupt signal input from the video A/D converter
65 ADV7181_SDA I/O Two-way I2C serial data with the video A/D converter
66 NC O Not used
67 ADV7181_SCLK O I2C serial data transfer clock signal output to the video A/D converter
68 HDMI_OUTA_5VPWR O
Power supply on/off control signal output terminal for HDMI OUT A ARC connector
“H”: power on
69 HDMI_OUTB_5VPWR O
Power supply on/off control signal output terminal for HDMI OUT B connector
“H”: power on
70 ADV_1.8VCONT O Power supply on/off control signal output terminal for video processor “H”: power on
71 ADV_RST O Reset signal output to the video processor “L”: reset
72 ADV_PDN O Power down signal output to the video processor “L”: power down
73 ADV_INT0 I Interrupt signal input terminal Not used
74 ADV_INT1 I Interrupt signal input from the video processor (for HDMI transmitter)
D-VIDEO BOARD IC3000 MB91F627PMC-G-JNE1 (VIDEO SYSTEM CONTROLLER)