Sur-Gard System Five - Page 124

7.0 SG-DRL5/DRL5E/DRL5-2L PSTN Line Cards
- 124 -
LLL = line number
AAAA = account code
CCCC = channel 1-4
s = space
CCCC = channel 5-8
s = space
C = channel 9
[DC4] terminator
On the SG-SystemIV this option also controls the Scantronics formats:
2-8-1,5-8-1,6-8-1 (9-digit channels) and 2-16-1,3-16-1,4-16-1,5-16-1,6-16-1 (17-digit channels).
Refer also to the 11 & 12 digit DTMF Option 1A0/2A0 for configuring conflicting formats.
When this option is programmed as 00, the SG-SystemIV will convert the outputs in the corresponding 2-2,3-2,4-2,5-2 format:
automation: 1RRLLLssssAAAAAAsXssYY[DC4]
printer: RR-LLL-AAAAAA-YY-Alarm
When this option is programmed as '01' the Scantronics formats will not be decoded and the received data is passed to the outputs.
automation:
8RRLLLAAAAAAsCCCCsCCCCsC[DC4] (9-digit channels)
8RRLLLAAAAAAsCCCCsCCCCsCCCCsCCCCsC[DC4]
(17-digit channels)
printer:
RR-LLL-AAAAAA--ccccccccc (9-digit channels)
RR-LLL-AAAAAA--ccccccccccccccccc] (17-digit channels)
The above examples are shown with 6-digit accounts, for accounts less than this, leading digits are not sent. For example, 2-8-1 will be output as:
8RRLLLAAsccccsccccsc[DC4]
RR-LLL-AA--ccccccccc
When this option is programmed as '02', the SG-DRL4 will perform the normal 4-2 conversion using the predefined individual event codes, instead of
Option 170/270 "Common Event Code". This will not affect other formats (Pulse, ITI, etc) that will use Option 170/270.
SG-DRL5 Option 1A0/2A0: 11 / 12-Digit DTMF
(Acron or Scantronics) - Default (00)
When this option is programmed as '00', if 11 or 12-digit DTMF is received, it will be decoded as ACRON Format.
When this option is programmed as '01', if 11 or 12-digit DTMF is received, it will be decoded as SCANTRONICS Format.
Incoming Format Decoded Format
00 11-digit DTMF Acron 3-8
00 12-digit DTMF Acron 4-8
01 11-digit DTMF Scantronics 2-8-1
01 12-digit DTMF Scantronics 3-8-1
SG-DRL5 Option 1A1/2A1: FBI RS-232
Default 01
To enable the computer for FBI Super Fast protocol, program Option 1A1/2A1 as '01'. When enabled, the computer output will be as indicated below:
JRRLLLssssssAAAATZZEss[DC4]
Where:
J = FBI protocol identifier
RR = receiver number
LLL = line number
s = spaces
AAAA = account code
T = zone type
ZZ = zone number, in hex.
E = event code
if E = 0 and T = 0 : listen in.
SG-DRL5 Option 1A2/2A2: Digit Replace
Default (00)
This option works with Option 177/277. When Option 1A2/2A2 is enabled, and Option 177/277 is programmed with an ASCII value, the receiver will
replace or insert an account code digit. Option 1A2/2A2 determines how to replace or insert a digit.
To replace a digit, set Option 1A2/2A2 to 0x where x is the digit to be replaced.
To insert a digit, set Option 1A2/2A2 to 8x where x is the digit in the account code, after which will be the inserted digit.